P0400 Exhaust Gas Recirculation Flow
Diagnostic trouble codes · Vehicles built Jan 2015 – Mar 2016
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
DESCRIPTION
The EGR system recirculates exhaust gases, and is controlled to the proper volume to be suitable for all driving conditions. The recirculated gas mixes with the intake air, allowing the EGR system to slow down engine combustion and lower the combustion temperature. This helps reduce NOx emissions.In order to increase circulation efficiency, the ECM adjusts the lift amount of the EGR valve and throttle valve.
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Decelerate from a speed of 50 km/h (80 mph) or more (release accelerator pedal for approximately 5 seconds) |
|
|
- HINT:
- DTC detection is not performed for 4 seconds after brake switch is turned ON or OFF.
MONITOR DESCRIPTION
When the target and actual positions of the EGR valve are different, the ECM interprets this as a malfunction of the EGR valve and illuminates the MIL.

WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.
- After warming up the engine, DTC P0400 is set 1 second or more after quickly accelerating the engine from idling.
- Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. CHECK OTHER DTC OUTPUT |
Connect the GTS to the DLC3.
Turn the ignition switch ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
- Result:
Tester Display
Proceed to
P0400
A
P0400 and P0405 and/or P0406
B
- HINT:
- If any other codes besides DTC P0400 are output, perform troubleshooting for those DTCs first.
|
|
||||
| A | |
| 2. CHECK VACUUM PUMP ASSEMBLY |
Check the negative pressure of the vacuum pump (Click here).
- Standard:
- More than 86.7 kPa (650 mmHg, 26 in.Hg)
|
|
||||
| OK | |
| 3. CHECK VACUUM HOSES |
Check the vacuum hoses.
- OK:
- The hoses are not damaged and securely connected.
|
|
||||
| OK | |
| 4. CHECK TERMINAL VOLTAGE (VRV FOR EGR) |
Disconnect the VRV for EGR connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D55-1 - Body ground
Ignition switch ON
11 to 14 V
*a
Front view of wire harness connector
(to VRV for EGR)
Reconnect the VRV for EGR connector.
|
|
||||
| OK | |
| 5. INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY (VRV FOR EGR) |
Check the Electric EGR control valve assembly (VRV for EGR) (Click here).
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (VRV FOR EGR - ECM) |
Disconnect the VRV for EGR connector.
Disconnect the ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D55-2 - D105-83 (EGR)
Always
Below 1 Ω
D55-2 or D105-83 (EGR) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 7. INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY (EGR VALVE ASSEMBLY) |
Check the EGR valve assembly (Click here).
- OK:
- The valve is not stuck and does not have heavy carbon deposits
|
|
||||
| OK | ||
| ||
| 8. CHECK HARNESS AND CONNECTOR (VRV FOR EGR - NO. 1 INTEGRATION RELAY) |
Remove the No. 1 integration relay from the No. 1 engine room relay block and junction block assembly.
Disconnect the integration relay connector.
Disconnect the VRV for EGR connector.
Measure the resistance of the wire harness side connectors.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
10B-4 - D55-1
Always
Below 1 Ω
10B-4 or D55-1 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
