2014-2019 Hiace · Service Manual ENGINE

P1520 Stop Light Switch Circuit

Diagnostic trouble codes · Vehicles built from Oct 2014

DESCRIPTION

In this system, the signal of the stop light switch is used to judge whether the stop light system is abnormal or not.
The stop light switch has a duplex system (signals STP and ST1-) to memorize the abnormality when the signals of depressing and releasing the brake pedal are detected simultaneously.

HINT:
Normal condition is as shown in the table.
Signal
Brake pedal released
In transition
Brake pedal depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF
DTC No.
DTC Detection Condition
Trouble Area
P1520
When STP (without depressing the brake pedal) and ST1- (with the brake pedal depressed) signals continue for longer than 0.5 seconds with the ignition switch ON.
  1. Open or short in stop light switch signal circuit
  2. Stop light switch assembly
  3. ECM


WIRING DIAGRAM

A318863E03

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK STOP LAMP SWITCH ASSEMBLY (TERMINAL B VOLTAGE)

  1. A253393E14
    Disconnect the stop light switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B2-2 - Body ground
    Always
    11 to 14 V
    B2-4 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT STOP LAMP SWITCH ASSEMBLY

  1. A072924E02
    Disconnect the stop light switch assembly connector.

  1. Check the resistance between each pair of the terminals.

    Standard Resistance:
    Switch Position
    Tester Connection
    Specified Condition
    Switch pin free
    1 - 2
    Below 1 Ω
    Switch pin pushed in
    1 - 2
    10 kΩ or higher
    Switch pin free
    3 - 4
    10 kΩ or higher
    Switch pin pushed in
    3 - 4
    Below 1 Ω



NG
REPLACE STOP LAMP SWITCH ASSEMBLY
OK


3. INSPECT ECM (STP AND ST1- VOLTAGE)
A275087E14
  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Brake Pedal Condition
    Specified Condition
    B74-26 (ST1-) - Body ground
    Released
    11 to 14 V
    Depressed
    Below 1.5 V
    B74-27 (STP) - Body ground
    Released
    Below 1.5 V
    Depressed
    11 to 14 V

    Text in Illustration 
    *a
    Brake Pedal Depressed
    *b
    Brake Pedal Released
    *c
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P1290 Radiator / Engine Coolant Temperature Circuit (from Oct 2014)P1611 ECM/PCM Processor / Run Pulse (Oct 2014 – Dec 2014) →