2014-2019 Hiace · Service Manual COMMUNICATION SYSTEM

Short in CAN Bus Lines

Circuit diagnosis · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.
Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.
  1. Short between CAN bus lines
  2. ECM
  3. Air conditioning amplifier assembly*1
  4. Certification ECU (smart key ECU assembly)*2
  5. Headlight leveling ECU assembly*3
  6. Combination meter assembly
  7. CAN junction connector
  1. *1: w/ Air Conditioning System, except 5L-E
  2. *2: w/ Smart Entry and Start System
  3. *3: for LED Headlight

WIRING DIAGRAM

C299905E01

INSPECTION PROCEDURE

NOTICE:
For vehicles with a smart entry and start system:
Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (Click here).

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    For vehicles with an airbag system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR SHORT IN CAN BUS WIRES (DLC3 CAN BRANCH WIRE)

  1. C253362E35
    Disconnect the H64 CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H23-6 (CANH) - H23-14 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3. CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NOTICE:
For vehicles without an air conditioning system or with 5L-E engine type, go to "Check for Short in CAN Bus Wires (CAN Junction Connector - Certification ECU)".

  1. C297944E01
    Disconnect the CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H62-1 (CANH) - H62-2 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector)



NG
Go to step 8
OK


4. CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR - CERTIFICATION ECU)

NOTICE:
For vehicles without a smart entry and start system, go to "Check for Short in CAN Bus Wires (CAN Junction Connector - Headlight Leveling ECU Assembly)".

  1. C297944E02
    Disconnect the CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H66-1 (CANH) - H66-2 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector)



NG
Go to step 10
OK


5. CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR - HEADLIGHT LEVELING ECU ASSEMBLY)

NOTICE:
For vehicles with a halogen headlight, go to "Check for Short in CAN Bus Wires (CAN Junction Connector - ECM)".

  1. C297944E03
    Disconnect the CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H90-1 (CANH) - H90-2 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector)



NG
Go to step 12
OK


6. CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR - ECM)

  1. C297944E04
    Disconnect the CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H63-1 (CANH) - H63-2 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector)



NG
Go to step 14
OK


7. CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

  1. C297944E05
    Disconnect the CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H65-1 (CANH) - H65-2 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector)



NG
Go to step 16
OK

REPLACE CAN JUNCTION CONNECTOR

8. CONNECT CONNECTOR
  1. Reconnect all wire harness CAN junction connectors.


NEXT


9. CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY)

  1. C221258E03
    Disconnect the air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H18-10 (CANH) - H18-11 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Air Conditioning Amplifier Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

10. CONNECT CONNECTOR
  1. Reconnect all wire harness CAN junction connectors.


NEXT


11. CHECK FOR SHORT IN CAN BUS WIRES (CERTIFICATION ECU)

  1. C297939E01
    Disconnect the certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    B76-40 (CANH) - B76-18 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Certification ECU [Smart Key ECU Assembly])



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CANH, CANL)
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

12. CONNECT CONNECTOR
  1. Reconnect all wire harness CAN junction connectors.


NEXT


13. CHECK FOR SHORT IN CAN BUS WIRES (HEADLIGHT LEVELING ECU ASSEMBLY)

  1. C268313E17
    Disconnect the headlight leveling ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A39-6 (CANH) - A39-7 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Headlight Leveling ECU Assembly)
    Result 
    Result
    Proceed to
    OK (for LHD)
    A
    OK (for RHD)
    B
    NG
    C



B
REPLACE HEADLIGHT LEVELING ECU ASSEMBLY (Click here)

C
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO HEADLIGHT LEVELING ECU ASSEMBLY (CANH, CANL)
A

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY (Click here)

14. CONNECT CONNECTOR
  1. Reconnect all wire harness CAN junction connectors.


NEXT


15. CHECK FOR SHORT IN CAN BUS WIRES (ECM)

  1. C299906E01
    Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1KD-FTV (w/ DPF) 
    Tester Connection
    Switch Condition
    Specified Condition
    B73-7 (CANH) - B73-6 (CANL)
    Ignition switch off
    108 to 132 Ω
    for 1KD-FTV (w/o DPF) 
    Tester Connection
    Switch Condition
    Specified Condition
    B72-7 (CANH) - B72-6 (CANL)
    Ignition switch off
    108 to 132 Ω
    for 2KD-FTV 
    Tester Connection
    Switch Condition
    Specified Condition
    B88-6 (CANH) - B88-7 (CANL)
    Ignition switch off
    108 to 132 Ω
    for 1TR-FE, 2TR-FE 
    Tester Connection
    Switch Condition
    Specified Condition
    B71-8 (CANH) - B71-9 (CANL)
    Ignition switch off
    108 to 132 Ω
    for 5L-E 
    Tester Connection
    Switch Condition
    Specified Condition
    B74-10 (CANH) - B74-11 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *A
    for 1KD-FTV (w/ DPF)
    *B
    for 1KD-FTV (w/o DPF)
    *C
    for 2KD-FTV
    *D
    for 1TR-FE, 2TR-FE
    *E
    for 5L-E
    *a
    Front view of wire harness connector
    (to ECM)

HINT:
*: Replacement procedure:

  1. for 1KD-FTV (Click here).
  2. for 2KD-FTV (Click here).
  3. for 1TR-FE (Click here).
  4. for 2TR-FE (Click here).
  5. for 5L-E (Click here).


NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
OK

REPLACE ECM*

16. CONNECT CONNECTOR
  1. Reconnect all wire harness CAN junction connectors.


NEXT


17. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)

  1. C221258E04
    Disconnect the combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H20-23 (CANH) - H20-22 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Combination Meter Assembly)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)


← Open in CAN Main Bus Line (from Jan 2017)Short in CAN Bus Lines (Jan 2015 – Mar 2016) →