2014-2019 Hiace · Service Manual COMMUNICATION SYSTEM

CAN Bus Line

Circuit diagnosis · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

Measure the resistance from the DLC3 before checking the CAN bus wires to troubleshoot the CAN communication system.

WIRING DIAGRAM

C299905E01

INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    For vehicles with an airbag system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR OPEN CIRCUIT IN DLC3 BRANCH WIRE AND V1 BUS CIRCUIT CAN MAIN WIRE AND SHORT CIRCUIT (CANH - CANL)

  1. C253362E35
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Value
    Result
    H23-6 (CANH) - H23-14 (CANL)
    Ignition switch off
    OK (54 to 69 Ω)
    A
    H23-6 (CANH) - H23-14 (CANL)
    Ignition switch off
    NG (Higher than 70 Ω)
    B
    H23-6 (CANH) - H23-14 (CANL)
    Ignition switch off
    NG (Below 53 Ω)
    C

    Text in Illustration 
    *a
    Front view of DLC3



B
GO TO OPEN IN CAN MAIN BUS LINE (Click here)

C
GO TO SHORT IN CAN BUS LINES (Click here)
A


3. CHECK FOR SHORT TO B+ IN CAN V1 BUS (CANH, CANL - BAT)

  1. C253362E36
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Value
    H23-6 (CANH) - H23-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H23-14 (CANL) - H23-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
GO TO SHORT TO B+ IN CAN BUS LINE (Click here)
OK


4. CHECK FOR SHORT TO GND IN CAN V1 BUS (CANH, CANL - CG)

  1. C253362E37
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Value
    H23-6 (CANH) - H23-4 (CG)
    Ignition switch off
    200 Ω or higher
    H23-14 (CANL) - H23-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
GO TO SHORT TO GND IN CAN BUS LINE (Click here)
OK

GO TO HOW TO PROCEED WITH TROUBLESHOOTING (Click here)


← AFS ECU Communication Stop Mode (from Jan 2017)CAN Bus Line (Jan 2015 – Mar 2016) →