2014-2019 Hiace · Service Manual COMMUNICATION SYSTEM

Open in CAN Main Bus Line

Circuit diagnosis · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

There may be an open circuit in the CAN main wire and/or DLC3 CAN branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.
Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.
  1. CAN main wire and connector
  2. ECM
  3. Combination meter assembly
  4. CAN junction connector
  5. DLC3 CAN branch wire or connector

WIRING DIAGRAM

C299904E01

INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    For vehicles with an airbag system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR OPEN IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)

  1. C253362E35
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H23-6 (CANH) - H23-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of DLC3

    NOTICE:
    When the measured value is 133 Ω or higher and a CAN communication system DTC is output, there may be a fault besides disconnection of the DLC3 branch line. For that reason, troubleshooting should be performed again from How to Proceed with Troubleshooting after repairing the trouble area (Click here).



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3. CHECK FOR OPEN IN CAN BUS WIRE (CAN JUNCTION CONNECTOR - ECM)

  1. C297944E04
    Disconnect the CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H63-1 (CANH) - H63-2 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector)



NG
Go to step 5
OK


4. CHECK FOR OPEN IN CAN BUS WIRE (CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

  1. C297944E05
    Disconnect the CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H65-1 (CANH) - H65-2 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector)



NG
Go to step 7
OK

REPLACE CAN JUNCTION CONNECTOR

5. CONNECT CONNECTOR
  1. Reconnect all wire harness CAN junction connectors.


NEXT


6. CHECK FOR OPEN IN CAN BUS WIRE (ECM - CAN JUNCTION CONNECTOR)

  1. C299906E01
    Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1KD-FTV (w/ DPF) 
    Tester Connection
    Switch Condition
    Specified Condition
    B73-7 (CANH) - B73-6 (CANL)
    Ignition switch off
    108 to 132 Ω
    for 1KD-FTV (w/o DPF) 
    Tester Connection
    Switch Condition
    Specified Condition
    B72-7 (CANH) - B72-6 (CANL)
    Ignition switch off
    108 to 132 Ω
    for 2KD-FTV 
    Tester Connection
    Switch Condition
    Specified Condition
    B88-6 (CANH) - B88-7 (CANL)
    Ignition switch off
    108 to 132 Ω
    for 1TR-FE, 2TR-FE 
    Tester Connection
    Switch Condition
    Specified Condition
    B71-8 (CANH) - B71-9 (CANL)
    Ignition switch off
    108 to 132 Ω
    for 5L-E 
    Tester Connection
    Switch Condition
    Specified Condition
    B74-10 (CANH) - B74-11 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *A
    for 1KD-FTV (w/ DPF)
    *B
    for 1KD-FTV (w/o DPF)
    *C
    for 2KD-FTV
    *D
    for 1TR-FE, 2TR-FE
    *E
    for 5L-E
    *a
    Front view of wire harness connector
    (to ECM)

HINT:
*: Replacement procedure:

  1. for 1KD-FTV (Click here).
  2. for 2KD-FTV (Click here).
  3. for 1TR-FE (Click here).
  4. for 2TR-FE (Click here).
  5. for 5L-E (Click here).


NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - CAN JUNCTION CONNECTOR)
OK

REPLACE ECM*

7. CONNECT CONNECTOR
  1. Reconnect all wire harness CAN junction connectors.


NEXT


8. CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - CAN JUNCTION CONNECTOR)

  1. C221258E04
    Disconnect the combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H20-23 (CANH) - H20-22 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Combination Meter Assembly)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (COMBINATION METER ASSEMBLY - CAN JUNCTION CONNECTOR)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)


← CAN Bus Line (from Jan 2017)Open in CAN Main Bus Line (Jan 2015 – Mar 2016) →