Lack of Power or Hesitation
Circuit diagnosis · Vehicles built from Jan 2017
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
DESCRIPTION
| Malfunction Condition |
Main Trouble Area |
Related Trouble Area |
|
(a) Injector assembly malfunctions
|
|
- HINT:
- Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors causing the malfunction.
- Check that the vehicle has not been modified in any way prior to the vehicle inspection.
- This troubleshooting procedure checks for the cause of an obvious lack of engine power while the vehicle is being driven (such as the maximum speed being extremely low).
- Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors causing the malfunction.
| Faults and Symptoms of Common Rail Diesel Components |
Engine Control
Mass Air Flow Meter Main fault
Decrease in performance (foreign matter is stuck)
Symptoms
Lack of power, black smoke
Data List
MAF
- HINT:
- The maximum fuel injection volume is controlled according to the output from the mass air flow meter.
Intake System Symptom and Corresponding Main Fault
- Lack of power (no black smoke) due to air filter blockage or crushed or leaking air duct
- Black smoke (no lack of power) due to leakage between the turbo and intake manifold
Data List
- MAP
- Target Booster Pressure
When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds, then a lack of power will be felt.
- MAF
Turbocharger System Main fault
- Air leak in the turbocharged air passage
- Turbocharger (turbine, bearing, variable nozzle)
Symptoms
Lack of power (when vehicle is starting, under heavy load)
(Black smoke is not emitted when racing while vehicle is stopped)
Data List
MAP, Target Booster Pressure - When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds, then a lack of power will be felt.
- With the ignition switch ON or during idling, MAP = atmospheric pressure (standard atmospheric pressure = 101 kPa). When the engine speed is about 1500 rpm or more, the turbocharger starts to take effect and MAP becomes higher than atmospheric pressure.
- Atmospheric pressure decreases by 1 kPa each time elevation increases by 100 m, and is also affected by the current weather conditions.
Exhaust System Main fault
Blockage
Symptoms
Lack of power (high engine speed, under heavy load)
Data List
MAP, Target Booster Pressure
When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds, then a lack of power will be felt.
Glow System Main fault
Glow system malfunction
Symptoms
Difficult to start, rough idle, knocking, white smoke (when cold)
Data List
Check the glow plug indicator light
Diagnostic Point
Measure the resistance of the glow plug
Engine - 1 Main fault
Damaged, seized up
Symptoms
Cannot crank, crank speed is low, strange noise
Engine - 2 Main fault
Loss of compression
Symptoms
Rough idle (lack of power always)
Data List
Engine Speed of Cyl# - When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression.
- When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder.
Diesel Injection
Fuel Supply Pump Assembly Main fault
-
Symptoms
Difficult to start, engine stalling, rough idle, lack of power
Data List
Common Rail Pressure, Target Common Rail Pressure, Target Pump SCV Current - Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).
- If the Common Rail Pressure is 20000 kPa below the target pressure, then a lack of power will be felt.
- If the Common Rail Pressure is below 25000 kPa, then idling will be rough.
- If Target Pump SCV Current is 3000 mA or higher, the suction control valve may be stuck.
- HINT:
- The Common Rail Pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.
- When Target Pump SCV Current is 3000 mA or higher, the suction control valve has a tendency to become stuck.
- The Common Rail Pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.
Diagnostic Trouble Code
Even if Common Rail Pressure is below Target Common Rail Pressure, a DTC will not be stored.
Fuel Filter Element Sub-assembly Main fault
Blockage
Symptoms
Difficult to start, engine stalling, rough idle, lack of power
Data List
Common Rail Pressure, Target Common Rail Pressure - Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).
- If the Common Rail Pressure is 20000 kPa below the target pressure, then a lack of power will be felt.
- If the Common Rail Pressure is below 25000 kPa, then idling will be rough.
- HINT:
- The Common Rail Pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.
Diagnostic Trouble Code
Even if Common Rail Pressure is below Target Common Rail Pressure, a DTC will not be stored.
Injector Assembly Main fault
Blockage
Symptoms
Rough idle, lack of power, black smoke, white smoke, knocking
Data List
Injection Feedback Val - When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute.
Injector Driver Main fault
Circuit fault: The injector assembly does not open.
Symptoms
Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking
Data List
Same as injector assembly
Diagnostic Trouble Code
When the injector driver has a fault, some DTCs may be stored.
Fuel Pressure Sensor Main fault
Open circuit, decrease in performance (foreign matter is stuck)
Symptoms
Difficult to start, rough idle, engine stall, lack of power
Data List
Common Rail Pressure, Target Common Rail Pressure - Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).
Diagnostic Code
When the fuel pressure sensor has a fault, some DTCs may be stored.
Irregular Fuel Main fault
-
Symptoms
Difficult to start, rough idle (especially when cold)
- Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).
Diesel EGR
EGR System Main fault
- Does not move smoothly
- Does not close fully
Symptoms
- Rough Idle
- EGR valve stuck closed: A loud turbocharger sound.
- EGR valve stuck open: Difficult to start (does not stall), black smoke, white smoke (when engine is cold), lack of power, jerking (If there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt. Also, when racing the engine, there will be some black smoke).
Data List
Actual EGR Valve Pos., Target EGR Valve Pos - Generally, Actual EGR Valve Pos. = Target EGR Valve Pos +/-5% (fully closed: 0%, fully open: 100%).
- Using the EGR valve Active Test, check whether Actual EGR Valve Pos. follows Target EGR Valve Pos (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs).
- EGR valve is fully closed when the ignition switch ON (engine stopped).
- EGR valve opens to the halfway point at idling after the engine is warmed up.
- When the EGR valve does not close, MAF (Mass Air Flow) decreases when the vehicle is accelerated at full throttle. MAP also decreases in comparison to Target Booster Pressure, however there is not a large difference.
- When leaving the vehicle idling the normal range of EGR Close Lrn. Val. is 0 to 1 V.
- In cases EGR Close Lrn. Val. is out of the normal range (0 to 1 V), it is possible that the EGR valve cannot completely close.
- Does not move smoothly
Diesel Throttle
Diesel Throttle System Main fault
Stuck, does not move smoothly
Symptoms
- Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.
- Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.
Data List
- Actual Throttle Position (fully closed: 100%, fully open: 0%)
- When the ignition switch ON (engine stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is fully closed temporarily.
- Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.
| Data List Related to Lack of Power |
- Engine Speed
- MAP
- MAF
- Intake Air
- Coolant Temp
- Target Common Rail Pressure
- Common Rail Pressure
- Target Pump SCV Current
- Injection Feedback Val #1 (to #4)
- Injection Volume
- Actual Throttle Position
- Target EGR Valve Pos
- Actual EGR Valve Pos
INSPECTION PROCEDURE
| Explanation of Symptom |
| Lack of Power |
The power of the diesel engine is determined by the quantity of injected fuel and the quantity of intake air. The quantity of injected fuel is determined by the fuel pressure and the amount of time the injector assembly is open. Basically, the fuel pressure is controlled so that it reaches the target fuel pressure. The throttle valve does not restrict air flow volume, so the manifold absolute pressure is almost the same as atmospheric pressure when idling. At more than approximately 1500 rpm, the turbo starts to operate causing the manifold absolute pressure to become higher than atmospheric pressure. The manifold absolute pressure is controlled so that it reaches the Target Booster Pressure when accelerating the vehicle at full throttle. Also, when accelerating the vehicle at full throttle, the throttle is fully open and the EGR valve is fully closed, preserving the mass air flow. |
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
- After replacing an injector assembly, the ECM needs registration (Click here).
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
| 1. READ OUTPUT DTC (RELATING TO ENGINE) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTCs.
Result Result
Proceed to
No DTCs are output
A
Engine related DTCs are output
B
- HINT:
- If only DTC P1608 is output, proceed to step 2.
|
|
||||
| A | |
| 2. TAKE SNAPSHOT DURING IDLING AND 4000 RPM (PROCEDURE 2) |
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Lack of Power.
With no load after the engine is warmed up, take a snapshot when idling and at 4000 rpm.
- HINT:
- A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.
- The shift lever should be in neutral and the A/C switch and all accessory switches should be off.
- A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.
| NEXT | |
| 3. TAKE SNAPSHOT DURING LACK OF POWER (PROCEDURE 3) |
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Lack of Power.
Check for a lack of power during the driving test.
- HINT:
- A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.
- Move the shift lever to 2nd gear and accelerate the vehicle with the accelerator pedal fully depressed (obey all laws and regulations, and pay attention to traffic conditions while driving the vehicle). Then, check the Data List with the engine warmed up and idling (the shift lever should be in neutral and the A/C switch and all accessory switches should be off).
- A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.
Result Result
Proceed to
Apparent lack of power is present
A
Apparent lack of power is not present
B
|
|
||||
| A | |
| 4. CHECK SNAPSHOT (MAP AND MAF) |
Check MAP and MAF in the snapshot taken in procedure 2 when the engine was running at 4000 rpm with no load.
Result Result
Proceed to
MAP is 105 kPa or higher and MAF is 84 gm/sec or more*1
A
MAP is below 90 kPa*2
B
Except above*3
C
- HINT:
- The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.
- Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.
- *1: There may be a problem in the fuel injection system or intake system.
- *2: There may be a problem in the turbocharger system.
- *3: There may be a problem in the intake system or a problem with the EGR valve (valve stuck open or valve does not close).
|
|
||||
|
|
||||
| A | |
| 5. CHECK SNAPSHOT (COMMON RAIL PRESSURE, TARGET COMMON RAIL PRESSURE, MAP AND TARGET BOOSTER PRESSURE) |
Check Common Rail Pressure, Target Common Rail Pressure, MAP and Target Booster Pressure in the snapshot taken in procedure 3 when the vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear.
Result Result
Proceed to
MAP is below 170 kPa at an engine speed of 3000 rpm
A
Difference between Common Rail Pressure and Target Common Rail Pressure is 20000 kPa or more
B
Except above
C
- HINT:
- The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.
Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.
- The engine speed must be 1500 rpm or less before performing the inspection in which the accelerator pedal is fully depressed and the engine is accelerated to a speed of 3000 rpm.
- If the turbocharger movement is not smooth, etc., the value of MAP in the snapshot taken during lack of power will not reach the target value.
When the accelerator pedal is fully depressed and the engine speed is 3000 rpm, the MAP should be higher than 195 kPa.
- The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.
|
|
||||
|
|
||||
| A | |
| 6. CHECK INTAKE SYSTEM |
Check for air leaks and blockages between the air cleaner case and turbocharger, and between the turbocharger and intake manifold.
- HINT:
- Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.
- Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.
- Using your hand, check whether the pipes and hoses in the intake system are securely connected.
- By applying soapy water and revving up the engine, air leaks from the intake system can be checked by checking for bubbles.
- Check for any modifications in the intake system made by the user.
- Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.
- OK:
- No leakage or blockage.
|
|
||||
| OK | |
| 7. CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER |
Clean the fuel filter case and replace the fuel filter.
- HINT:
- Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.
| NEXT | |
| 8. REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS |
Replace the injector assemblies (Click here).
- NOTICE:
- When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
- Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
- If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
- If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
- If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.
- When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
| NEXT | |
| 9. BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system (Click here).
| NEXT | |
| 10. REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING |
Register the injector compensation code (Click here).
Perform the injector pilot quantity learning (Click here).
| NEXT | |
| 11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||
| 12. READ VALUE USING GTS (MAP AND ATMOSPHERIC PRESSURE) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.
Compare MAP to Atmosphere Pressure when the ignition switch ON (do not start the engine).
- Standard:
- Difference between MAP and Atmosphere Pressure is less than 8 kPa.
- HINT:
- If MAP and Atmosphere Pressure have the same value, both are normal. If there is a difference of 8 kPa or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.
- Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.
- If MAP and Atmosphere Pressure have the same value, both are normal. If there is a difference of 8 kPa or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.
Result Result
Proceed to
MAP and Atmosphere Pressure have same value
A
MAP is different from actual atmospheric pressure
B
Atmosphere Pressure is different from actual atmospheric pressure
C
|
|
||||
|
|
||||
| A | |
| 13. CHECK AIR INTAKE SYSTEM |
Check for air leaks and blockages between the air cleaner case and turbocharger, and between the turbocharger and intake manifold.
Result Result
Proceed to
Leaks and/or blockages exist in the intake system
A
No leaks or blockages in the intake system
B
- HINT:
- Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.
- Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.
- Using your hand, check whether the pipes and hoses in the intake system are securely connected.
- When inspecting for a clogged intake system (cause of low MAP), check the following points:
- Clogged air cleaner
- Clogged intake hose
- Diesel throttle valve stuck in closed position
- Check for any modifications in the intake system made by the user.
- Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.
|
|
||||
| B | |
| 14. CHECK TURBOCHARGER SUB-ASSEMBLY |
Check for turbocharger sub-assembly (Click here).
|
|
||||
| OK | |
| 15. CHECK FOR INTERMITTENT PROBLEMS |
Check for intermittent problems (Click here).
|
|
||||
| 16. REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR |
Replace the manifold absolute pressure sensor.
|
|
||||
| 17. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 18. REPAIR OR REPLACE AIR INTAKE SYSTEM |
Repair or replace the malfunctioning part in the air intake system.
|
|
||||
| 19. REPLACE TURBOCHARGER SUB-ASSEMBLY |
Replace the turbocharger sub-assembly (Click here).
| NEXT | |
| 20. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||
| 21. INSPECT CLOGGED FUEL PIPE |
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Injection.
With no load after the engine is warmed up, take a snapshot when idling and vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear.
Check the Target Common Rail Pressure and Common Rail Pressure value.


Result Result
Proceed to
While idling the vehicle, "Common Rail Pressure" deviates from the normal range and varies periodically with a period of approximately 2 seconds or more*1
A
"Common Rail Pressure" is normal while idling the vehicle, but "Common Rail Pressure" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear*2
Except above
B
- NOTICE:
- *1: The cause may be a squashed or blocked fuel pipe or hose.
- *2: The cause may be a clogged fuel filter.
- *1: The cause may be a squashed or blocked fuel pipe or hose.
|
|
||||
| B | |
| 22. REPLACE SUCTION CONTROL VALVE |
Replace the suction control valve (Click here).
|
|
||||
| 23. REPAIR OR REPLACE CLOGGED FUEL LINE |
Repair or replace the clogged (including frozen fuel) fuel pipe.
Replace the fuel filter element sub-assembly.
- HINT:
- If "Common Rail Pressure" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear, replace the fuel filter element sub-assembly.
| NEXT | |
| 24. BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system (Click here).
| NEXT | |
| 25. PERFORM FUEL SUPPLY PUMP INITIALIZATION |
Perform fuel supply pump initialization (Click here).
| NEXT | |
| 26. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Common Rail Pressure, Target Common Rail Pressure.
Take a snapshot with the GTS during the Active Test.
Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Common Rail Pressure) when the "Test the Fuel Leak" Active Test is performed.
- HINT:
- In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


- OK:
- The difference between the target fuel pressure seconds after the Active Test starts is less than 10000 kPa.
- HINT:
- "Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.
- "Common Rail Pressure" is the actual fuel pressure.
- "Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.
| NEXT | ||
| ||
| 27. CHECK AIR INTAKE SYSTEM |
Check for air leaks and blockages between the air cleaner case and turbocharger, and between the turbocharger and intake manifold.
Result Result
Proceed to
No leaks or blockages in the intake system
A
Leaks and/or blockages exist in the intake system
B
- HINT:
- Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.
- Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.
- Using your hand, check whether the pipes and hoses in the intake system are securely connected.
- The swirl control valve does not move due to deposits or the diaphragm not being air-tight, etc., and the specified output performance cannot be obtained.
- If operating normally, when the engine is started, the swirl control valve quickly moves from fully open to fully closed.
- By applying soapy water and revving up the engine, air leaks from the intake system can be checked by checking for bubbles.
- Make sure that the hose between the manifold absolute pressure sensor and intake manifold is not loose or disconnected.
- Check for any modifications in the intake system made by the user.
- Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.
|
|
||||
| A | |
| 28. PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR VALVE CLOSE) |
Connect the GTS to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Read the MAF value displayed on the GTS while the engine is idling.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the EGR Valve Close.
Read the MAF value when the EGR valve is closed using the Active Test function.
- HINT:
- If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.
- Before performing the diagnosis, confirm that the EGR valve target opening angle is not 0%.
- If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.
Result Active Test
Result
Proceed to
Activate the EGR Valve Close:
Off (Open) to On (Closed)
MAF value does not change
A
MAF value changes
B
- NOTICE:
- As the measured values may differ from those shown below due to factors such as differences in measuring environments and changes in vehicle condition due to aging, do not use these values to determine whether the vehicle is malfunctioning or not.
- HINT:
- The problem may be a temporary one, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric EGR control valve assembly or mass air flow meter.
- Reference:
EGR Valve Condition (Opening)
Measuring Condition
MAF (Reference)
Open (70%)
- Atmosphere pressure: 101 kPa
- Intake air temperature: 30°C (86°F)
- Engine coolant temperature: 88°C (190°F)
3 to 40 gm/sec
Closed (0%)
38 to 52 gm/sec
- Atmosphere pressure: 101 kPa
|
|
||||
| A | |
| 29. READ VALUE USING GTS (MAF) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Read the value.
- Standard:
GTS Display
Condition
Specified Condition
MAF
Ignition Switch ON
Less than 0.63 gm/sec
|
|
||||
| OK | |
| 30. PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EGR COOLER BYPASS) |
Connect the GTS to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off and wait for 30 seconds.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Read the MAF value displayed on the GTS while the engine is idling.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for EGR Cooler Bypass / Data List / EGR Cooler Bypass Position.
- HINT:
- Whether the EGR is passing through the bypass side or cooler side during the Active Test can be confirmed by checking EGR Cooler Bypass Position.
Using the Active Test function, switch the EGR valve bypass switching valve between "Cooler" and "Bypass" a few times, and then check whether the MAF value changes after switching the valve from "Cooler" to "Bypass".
- HINT:
- If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.
Result GTS Display
Result
Proceed to
Activate the VSV for EGR Cooler Bypass:
Cooler to Bypass
MAF value does not change
A
MAF value changes
B
- HINT:
- If the EGR cooler is clogged, the mass air flow changes.
|
|
||||
| A | |
| 31. REMOVE DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY) |
Remove the electric EGR control valve assembly (Click here).
Visually check the electric EGR control valve assembly for deposits.If there are deposits, clean the electric EGR control valve assembly.
- NOTICE:
- When cleaning the electric EGR control valve assembly, make sure the valve is completely closed.
- When cleaning the electric EGR control valve assembly, perform initialization procedure (Click here).
- Do not forcibly open the valve, as it may be damaged or deformed.
- When cleaning the electric EGR control valve assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.
- When cleaning the electric EGR control valve assembly, make sure the valve is completely closed.
- HINT:
- If the EGR valve does not open properly or is stuck closed, the amount of intake air increases and combustion sounds and engine vibration may increase.
- If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power. In this case, clean the electric EGR control valve assembly.
- If the EGR valve does not open properly or is stuck closed, the amount of intake air increases and combustion sounds and engine vibration may increase.
Reinstall the electric EGR control valve assembly (Click here).
|
|
||||
| 32. REPAIR OR REPLACE AIR INTAKE SYSTEM |
Repair or replace the malfunctioning part in the air intake system.
|
|
||||
| 33. REPLACE MASS AIR FLOW METER |
Replace the mass air flow meter (Click here).
- HINT:
- If foreign matter is stuck inside the mass air flow meter, the output characteristics of the mass air flow meter may change, resulting in a malfunction.
- Before replacing the mass air flow meter, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.
- If foreign matter is stuck inside the mass air flow meter, the output characteristics of the mass air flow meter may change, resulting in a malfunction.
|
|
||||
| 34. REPLACE EGR COOLER |
Replace the EGR cooler (Click here).
| NEXT | |
| 35. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
|
|
||||
| OK | ||
| ||
| 36. PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EGR COOLER BYPASS) |
Connect the GTS to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off and wait for 30 seconds.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Read the MAF value displayed on the GTS while the engine is idling.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for EGR Cooler Bypass / Data List / EGR Cooler Bypass Position.
- HINT:
- Whether the EGR is passing through the bypass side or cooler side during the Active Test can be confirmed by checking EGR Cooler Bypass Position.
Using the Active Test function, switch the EGR valve bypass switching valve between "Cooler" and "Bypass" a few times, and then check whether the MAF value changes after switching the valve from "Cooler" to "Bypass".
- HINT:
- If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.
Result GTS Display
Result
Proceed to
Activate the VSV for EGR Cooler Bypass:
Cooler to Bypass
MAF value does not change
A
MAF value changes
B
- HINT:
- If the EGR cooler is clogged, the mass air flow changes.
|
|
||||
| A | |
| 37. CHECK FRONT EXHAUST PIPE ASSEMBLY (CATALYST CONVERTER) |
Remove the front exhaust pipe assembly (Click here).
Visually check for catalyst clogging or carbon deposits adhering to the inner wall of the exhaust pipe upstream of the catalyst.
- OK:
- Less than 10% of the cells are clogged.
Reinstall the front exhaust pipe assembly (Click here).
|
|
||||
| OK | |
| 38. INSPECT TURBOCHARGER SUB-ASSEMBLY |
Inspect the turbocharger sub-assembly (Click here).
|
|
||||
| OK | |
| 39. CHECK FOR INTERMITTENT PROBLEMS |
Check for intermittent problems (Click here).
|
|
||||
| 40. REPLACE EGR COOLER |
Replace the EGR cooler (Click here).
|
|
||||
| 41. REPLACE FRONT EXHAUST PIPE ASSEMBLY (CATALYST CONVERTER) |
Replace the front exhaust pipe assembly (Click here).
Perform Initialization procedure for DPF catalyst record clear (Click here).
|
|
||||
| 42. REPLACE TURBOCHARGER SUB-ASSEMBLY |
Replace the turbocharger sub-assembly (Click here).
| NEXT | |
| 43. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||
| 44. COMPARE WITH SIMILAR VEHICLE WITH SAME ENGINE |
Confirm the situation in which the lack of power was experienced by the customer again, and compare the driving feeling under the same conditions using a similar vehicle with the same engine while collecting data with the GTS.
- HINT:
- Confirm the state of the following conditions when the lack of power was experienced.
- Accelerator pedal position (vehicle load)
- Vehicle speed
- Engine coolant temperature
- Ambient temperature
- Driving conditions before the lack of power occurred
- Climate
- Road and traffic conditions
- When (what day) the problem was noticed
- Whether the problem occurs suddenly or gradually
- How often the problem occurs
- Why the customer felt there is a lack of power (e.g. the customer compared their vehicle with another vehicle, somebody told the customer that their vehicle has a lack of power, etc.)
- Level of lack of power (slight or drastic)
Result Result
Proceed to
Significant difference is found
A
Significant difference is not found
B
|
|
||||
| B | |
| 45. EXPLAIN THE INVESTIGATION RESULT TO CUSTOMER |
Vehicle performance is normal.There is no problem at this point in time. However, if the problem reoccurs, ask the customer to explain in detail the situation in which the problem occurred.The best course may be to have the customer ride in another vehicle with the same specifications to understand that there is no problem with the customer's vehicle.
| NEXT | ||
| ||
