P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input)
Diagnostic trouble codes · Vehicles built Jan 2015 – Mar 2016
Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
DESCRIPTION
The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0705 |
One of the following conditions is met: (A) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic):
|
|
MONITOR DESCRIPTION
This DTC indicate a problem with the park/neutral position switch assembly and the wire harness in the park/neutral position switch assembly circuit.The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.
For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch assembly sends a signal to the ECM according to the shift lever position (P, R, N, D or S). The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| DATA LIST |
- HINT:
- Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the GTS, read the Data List.
Engine and ECT Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Neutral Position SW Signal
Park/neutral position switch status/
ON or OFF
- ON: Shift lever in P or N
- OFF: Shift lever not in P or N
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
Shift SW Status (P Range)
Park/neutral position switch status/
ON or OFF
- ON: Shift lever in P
- OFF: Shift lever not in P
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
Shift SW Status (R Range)
Park/neutral position switch status/
ON or OFF
- ON: Shift lever in R
- OFF: Shift lever not in R
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
Shift SW Status (N Range)
Park/neutral position switch status/
ON or OFF
- ON: Shift lever in N
- OFF: Shift lever not in N
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
Sports Mode Selection SW
Sport mode select switch status/
ON or OFF
- ON: Shift lever in S, "+" or "-"
- OFF: Shift lever not in S, "+" or "-"
-
Shift SW Status (D Range)
Park/neutral position switch status/
ON or OFF
- ON: Shift lever in D, S, "+" or "-"
- OFF: Shift lever not in D, S, "+" or "-"
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
- ON: Shift lever in P or N
| 1. CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH) |
Disconnect the park/neutral position switch assembly connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D37-2 (RB) - Body ground
Ignition switch ON
11 to 14 V
D37-2 (RB) - Body ground
Ignition switch off
Below 1 V
Text in Illustration *a
Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE) |
Disconnect the park/neutral position switch assembly connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D37-4 (B) - Body ground
Ignition switch ON
11 to 14 V
D37-4 (B) - Body ground
Ignition switch off
Below 1 V
Text in Illustration *a
Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)
|
|
||||
| OK | |
| 3. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Disconnect the park/neutral position switch assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
4 (B) - 5 (L)
Shift lever in P or N
Below 1 Ω
2 (RB) - 6 (PL)
Shift lever in P
Below 1 Ω
2 (RB) - 1 (RL)
Shift lever in R
Below 1 Ω
2 (RB) - 9 (NL)
Shift lever in N
Below 1 Ω
2 (RB) - 7 (DL)
Shift lever in D, S, "+" or "-"
Below 1 Ω
4 (B) - 5 (L)
Shift lever not in P or N
10 kΩ or higher
2 (RB) - 6 (PL)
Shift lever not in P
10 kΩ or higher
2 (RB) - 1 (RL)
Shift lever not in R
10 kΩ or higher
2 (RB) - 9 (NL)
Shift lever not in N
10 kΩ or higher
2 (RB) - 7 (DL)
Shift lever not in D, S, "+" or "-"
10 kΩ or higher
Text in Illustration *a
Component without harness connected
(Park/Neutral Position Switch Assembly)
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH) |
Disconnect the transmission control switch connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
H72-6 (IG) - Body ground
Ignition switch ON
11 to 14 V
H72-6 (IG) - Body ground
Ignition switch off
Below 1 V
Text in Illustration *a
Front view of wire harness connector
(to Transmission Control Switch)
|
|
||||
| OK | |
| 5. INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY) |
Disconnect the transmission control switch connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
6 (IG) - 13 (S)
Shift lever in S, "+" or "-"
Below 1 Ω
6 (IG) - 13 (S)
Shift lever not in S, "+" or "-"
10 kΩ or higher
Text in Illustration *a
Component without harness connected
(Transmission Control Switch)
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH, TRANSMISSION CONTROL SWITCH - ECM) |
Disconnect the ECM connectors.

Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
D116-70 (P) - Body ground
- Ignition switch ON
- Shift lever in P
11 to 14 V
D116-65 (R) - Body ground
- Ignition switch ON
- Shift lever in R
11 to 14 V*
D116-39 (N) - Body ground
- Ignition switch ON
- Shift lever in N
11 to 14 V
D116-66 (D) - Body ground
- Ignition switch ON
- Shift lever in D, S, "+" or "-"
11 to 14 V
B94-59 (S) - Body ground
- Ignition switch ON
- Shift lever in S, "+" or "-"
11 to 14 V
D116-70 (P) - Body ground
- Ignition switch ON
- Shift lever not in P
Below 1 V
D116-65 (R) - Body ground
- Ignition switch ON
- Shift lever not in R
Below 1 V
D116-39 (N) - Body ground
- Ignition switch ON
- Shift lever not in N
Below 1 V
D116-66 (D) - Body ground
- Ignition switch ON
- Shift lever not in D, S, "+" or "-"
Below 1 V
B94-59 (S) - Body ground
- Ignition switch ON
- Shift lever not in S, "+" or "-"
Below 1 V
- Ignition switch ON
Text in Illustration *a
Front view of wire harness connector
(to ECM)
- HINT:
- *: The voltage will drop slightly due to lighting up of the back up light.
|
|
||||
| OK | ||
| ||
| 7. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM) |
Disconnect the D37 park/neutral position switch assembly connector.
Disconnect the B94 ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D37-4 (B) - B94-23 (NSW)
Always
Below 1 Ω
D37-4 (B) - Body ground
Always
10 kΩ or higher
B94-23 (NSW) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
