2014-2019 Hiace · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 from Apr 2016

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes, clean them with a brush and compressed air.


1. INSTALL OIL FILTER RECEIVER (w/ DPF)
  1. Install the oil filter receiver to the oil cooler cover with the 2 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


2. INSTALL OIL COOLER ASSEMBLY
  1. Install 2 new gaskets to the oil cooler.

  1. Install the oil cooler to the oil cooler cover with the 4 nuts.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }


3. INSTALL OIL COOLER COVER SUB-ASSEMBLY
  1. w/ DPF:

    1. Install a new gasket and the oil cooler cover with the 12 bolts.

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    2. Connect the No. 2 vacuum transmitting pipe with the 2 nuts and bolt.

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    3. Connect the 2 vinyl tubes.

    4. Install the drain cock plug.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    5. Connect the oil pressure sensor connector.

  1. w/o DPF:

    1. Install a new gasket and the oil cooler cover with the 13 bolts.

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    2. Connect the No. 2 vacuum transmitting pipe with the 2 nuts.

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    3. Connect the 2 vinyl tubes.

    4. Connect the oil pressure switch connector.


4. INSTALL OIL FILTER SUB-ASSEMBLY
  1. Check and clean the oil filter installation surface.

  1. Apply clean engine oil to the gasket of a new oil filter.

  1. Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.

  1. A113040E02
    Using SST, tighten the oil filter 3/4 of a turn by hand or with a common wrench.
    SST
    09228-07501  

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }


5. INSTALL NO. 2 WATER BY-PASS HOSE (w/ DPF)

6. INSTALL NO. 4 WATER BY-PASS HOSE (w/ DPF)

7. INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY (w/ DPF)

  1. A239515E02
    Temporarily install the No. 2 nozzle leakage pipe with the 3 bolts.

  1. Temporarily install a new gasket and the union bolt.

  1. Tighten the 3 bolts and union bolt.

    Torque:
    for union bolt:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    for bolt A:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }
    for bolt B:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


8. INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY (w/o DPF)
  1. Temporarily install the No. 2 nozzle leakage pipe with the 3 bolts.

  1. Temporarily install a new gasket and the union bolt.

  1. Tighten the 3 bolts and union bolt.

    Torque:
    for bolt:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }
    for union bolt:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the 3 fuel hoses.


9. INSTALL NO. 3 FUEL PIPE (w/ DPF)

  1. A239520E02
    Apply a light coat of fuel to the O-ring of the fuel check valve.

  1. Temporarily install the No. 3 fuel pipe with the 3 bolts.

  1. Temporarily install a new gasket and the fuel check valve.

  1. Temporarily install 2 new gaskets and the 2 union bolts.

  1. for Engine Rear Side:
    Tighten the 2 bolts and union bolt.

    Torque:
    for union bolt:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }
    for bolt:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. for Engine LH Side:

    1. Tighten the fuel check valve and bolt.

      Torque:
      for fuel check valve:
      32 N*m{ 321 kgf*cm , 23 ft.*lbf }
      for bolt:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    2. Using a 6 mm hexagon wrench, tighten the union bolt.

      Torque:
      21 N*m{ 214 kgf*cm , 15 ft.*lbf }

      NOTICE:
      Place the part of the gasket labeled A against the No. 3 fuel pipe as shown in the illustration and tighten the union bolt.


      A239514E01


10. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR (w/ DPF)
  1. Install the No. 2 exhaust manifold heat insulator with the 2 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


11. INSTALL NO. 3 NOZZLE LEAKAGE PIPE (w/ DPF)

  1. A239519E02
    Apply a light coat of fuel to the O-ring of the fuel check valve.

  1. Temporarily install the No. 3 nozzle leakage pipe with the bolt.

  1. Temporarily install a new gasket and the fuel check valve.

  1. Tighten the fuel check valve and bolt.

    Torque:
    for fuel check valve:
    32 N*m{ 321 kgf*cm , 23 ft.*lbf }
    for bolt:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Install the No. 2 injection pipe clamp with the bolt.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Connect the 3 fuel hoses.


12. INSTALL VACUUM SWITCHING VALVE BRACKET (w/o DPF)
  1. Install the vacuum switching valve bracket with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the 2 vacuum hoses and vacuum switching valve connector.


13. INSTALL FUEL INLET PIPE SUB-ASSEMBLY (w/o DPF)

NOTICE:
  1. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  2. Keep the fuel inlet pipe free of foreign matter.

  1. Temporarily install the fuel inlet pipe with the union nuts.

  1. Install the No. 2 injection pipe clamp with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the No. 1 injection pipe clamp with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    NOTICE:
    If a No. 1 injection pipe clamp is removed from the fuel inlet pipe, replace the No. 1 injection pipe clamp with a new one.

  1. Using a 17 mm union nut wrench, tighten the fuel inlet pipe union nut on the common rail side.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Using a 17 mm union nut wrench, tighten the fuel inlet pipe union nut on the fuel supply pump side.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).


14. INSTALL STARTER ASSEMBLY (w/ DPF)
  1. for 2.2 kW Type: (Click here)
  2. for 2.7 kW Type: (Click here)

15. INSTALL EGR COOLER WITH NO. 2 EGR VALVE ASSEMBLY (w/ DPF)
(Click here)

16. INSTALL EGR COOLER ASSEMBLY (w/o DPF)
(Click here)

17. ADD ENGINE COOLANT
  1. Firmly tighten the drain plugs.

  1. Fill the radiator reservoir assembly with engine coolant to the top of the inlet.

    Standard Capacity:
    Item
    Specified Condition
    w/o Heater
    13.2 liters (13.9 US qts, 11.6 Imp. qts)
    w/ Front Heater
    14.2 liters (15.0 US qts, 12.5 Imp. qts)
    w/ Front and Rear Heaters
    16.2 liters (17.1 US qts, 14.3 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. Use of improper coolants may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. Loosen the bleeder plug of the outlet housing.

  1. When air is bled and the engine coolant drains out, firmly tighten the bleeder plug.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. A142533
    Add engine coolant up to the B line mark in the radiator reservoir assembly and install the radiator reservoir cap sub-assembly.

  1. Warm up the engine until the thermostat opens.

    1. While the thermostat is open, circulate the engine coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by pressing the No. 3 radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. A142532
    After the engine cools down, check that the engine coolant level is between the LOW and FULL level marks.


18. ADD ENGINE OIL
  1. Add new engine oil.

    Standard Oil Grade:
    Item
    Oil Grade
    Oil Viscosity (SAE)
    w/ DPF
    ACEA C2
    (Using engine oil other than ACEA C2 may damage catalytic converter)
    - 0W-30
    - 5W-30
    w/o DPF
    G-DLD1, API CF-4, CF or ACEA B1
    (You may also use API CE or CD)
    - 5W-30
    - 10W-30
    - 15W-40
    - 20W-50


    Standard Capacity (w/ DPF):
    Item
    Fill Amount
    Drain and refill without oil filter change
    6.6 liters (7.0 US qts, 5.8 Imp. qts)
    Drain and refill with oil filter change
    6.8 liters (7.2 US qts, 6.0 Imp. qts)
    Dry fill
    7.5 liters (7.9 US qts, 6.6 Imp. qts)


    Standard Capacity (w/o DPF):
    Item
    Fill Amount
    Drain and refill without oil filter change
    6.8 liters (7.2 US qts, 6.0 Imp. qts)
    Drain and refill with oil filter change
    7.0 liters (7.4 US qts, 6.2 Imp. qts)
    Dry fill
    7.7 liters (8.1 US qts, 6.8 Imp. qts)

  1. Install the oil filler cap.


19. BLEED AIR FROM FUEL SYSTEM

  1. A239557E01
    Using the hand pump mounted on the fuel filter cap, bleed air from the fuel system. Continue pumping until the pump resistance increases.

    NOTICE:
    1. Hand pump pumping speed: Max. 2 strokes/ sec.
    2. The hand pump must be pushed with a full stroke during pumping.
    3. When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
    4. If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
    5. If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
    6. If air bleeding using the hand pump is incomplete, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.

  1. Check if the engine starts.

    NOTICE:
    1. Even if air bleeding using the hand pump has been completed, the starter may need to be cranked for 10 seconds or more to start the engine.
    2. Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
    3. Use a fully-charged battery.


    1. When the engine can be started, proceed to the next step.

    2. If the engine cannot be started, bleed air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.

  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs.

    1. w/ DPF: (Click here)
    2. w/o DPF: (Click here)

  1. Start the engine.*1

  1. A194065E03
    Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2

  1. Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3

  1. Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.

    A192848E05

    HINT:
    When the Active Test "Test the Fuel Leak" is used to change the pump control mode, the actual fuel pressure inside the common rail drops below the target fuel pressure when the Active Test is off, but this is normal and does not indicate a pump malfunction.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read Current DTCs.

  1. Clear the DTCs.

    1. w/ DPF: (Click here)
    2. w/o DPF: (Click here)

    HINT:
    It is necessary to clear the DTCs as DTC P1604 or P1605 may be stored when air is bled from the fuel system after replacing or repairing fuel system parts.

  1. Repeat steps *1 to *3.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read Current DTCs.

    OK:
    No DTCs are output.


20. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Hot, pressurized engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester to the radiator.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 137 kPa (1.4 kgf/cm2, 19.9 psi), and check that the pressure does not drop.

    HINT:
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.


21. INSPECT FOR OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the areas that were worked on.


22. INSPECT FOR FUEL LEAK
  1. Perform the Active Test.

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Active Test.

    5. Perform the Active Test.

      Tester Display
      Test Part
      Control Range
      Diagnostic Notes
      Test the Fuel Leak
      Pressurize common rail interior and check for fuel leaks
      Stop/Start
      1. Fuel pressure inside common rail increased to specified value and engine speed increased to 2000 rpm when Active Test is performed
      2. Above conditions preserved while Active Test is being performed


23. INSPECT ENGINE OIL LEVEL
  1. w/ DPF: (Click here)
  2. w/o DPF: (Click here)
← REMOVAL (from Apr 2016)INSTALLATION (Jan 2015 – Mar 2016) →