2014-2019 Hiace · Service Manual BRAKE

C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction

Diagnostic trouble codes · Vehicles built Jan 2015 – Mar 2016

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

DTC No.
DTC Detection Condition
Trouble Area
C1422
When vehicle speed is 3 km/h (2 mph) or more and stop light switch assembly is OFF, master cylinder pressure continuously exceeds 1.764 MPa (18.0 kgf/cm2, 255 psi) for 5 seconds or more.
  1. STOP NO. 1 fuse
  2. Stop light switch assembly
  3. Wire harness or connector
  4. Skid control ECU (Brake actuator assembly)
  5. Brake actuator assembly (Master cylinder pressure sensor)

WIRING DIAGRAM

Refer to DTC C1425 (Click here).

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Perform a road test.

  1. Check the DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC C1422 is output
    A
    DTCs C1422 and C1425 are output
    B



B
GO TO DTC CHART (Click here)
A


2. READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. In accordance with the display on the GTS, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch assembly / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the stop light switch assembly condition observed on the GTS changes according to brake pedal operation.

    OK:
    The GTS displays ON or OFF according to brake pedal operation.



NG
Go to step 5
OK


3. READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. In accordance with the display on the GTS, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Master Cylinder Pressure
    Master cylinder pressure sensor pressure / Min.: 0.00 MPa, Max.: 23.28 MPa
    Brake pedal operated: Proportional to pedal force
    Brake pedal released: 0.00 to 1.76 MPa
    -

    OK:
    Data List pressure is within standard range.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


4. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Perform a road test.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTC C1422 is not output
    A
    DTC C1422 is output
    B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

5. CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
  1. Turn the ignition switch off.

  1. Check the brake pedal height and stop light switch assembly installation (Click here).

    OK:
    The brake pedal height and stop light switch assembly installation are normal.



NG
ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


6. INSPECT STOP LIGHT SWITCH ASSEMBLY
  1. Remove the stop light switch assembly (Click here).

  1. Inspect the stop light switch assembly (Click here).

    OK:
    The stop light switch assembly is normal.



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


7. CHECK TERMINAL VOLTAGE (STP TERMINAL)

  1. C306843E04
    Turn the ignition switch off.

  1. Reinstall the stop light switch assembly (Click here).

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the B92 skid control ECU (brake actuator assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B92-35 (STP) - Body ground
    Stop light switch assembly on (Brake pedal depressed)
    8 to 14 V
    B92-35 (STP) - Body ground
    Stop light switch assembly off (Brake pedal released)
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)


← C1421 Open or Short in Master Cylinder Pressure Sensor (+ C1423, C1424, C142A, C1449) (from Dec 2017)C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction (Apr 2016 – Dec 2016) →