C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction
Diagnostic trouble codes · Vehicles built Jan 2017 – Nov 2017
Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
| DTC No. |
DTC Detection Condition |
Trouble Area |
| C1422 |
When vehicle speed is 3 km/h (2 mph) or more and stop light switch assembly is OFF, master cylinder pressure continuously exceeds 1.764 MPa (18.0 kgf/cm2, 255 psi) for 5 seconds or more. |
|
WIRING DIAGRAM
Refer to DTC C1425 (Click here).INSPECTION PROCEDURE
- NOTICE:
- When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click here).
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click here).
| 1. CHECK DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Perform a road test.
Check the DTCs (Click here).
- Result:
Result
Proceed to
DTC C1422 is output
A
DTCs C1422 and C1425 are output
B
|
|
||||
| A | |
| 2. READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
In accordance with the display on the GTS, read the Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stop Light SW
Stop light switch assembly / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Check that the stop light switch assembly condition observed on the GTS changes according to brake pedal operation.
- OK:
- The GTS displays ON or OFF according to brake pedal operation.
|
|
||||
| OK | |
| 3. READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
In accordance with the display on the GTS, read the Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Master Cylinder Pressure
Master cylinder pressure sensor pressure / Min.: 0.00 MPa, Max.: 23.28 MPa
Brake pedal operated: Proportional to pedal force
Brake pedal released: 0.00 to 1.76 MPa
-
- OK:
- Data List pressure is within standard range.
|
|
||||
| OK | |
| 4. RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Perform a road test.
Check if the same DTC is recorded (Click here).
- Result:
Result
Proceed to
DTC C1422 is not output
A
DTC C1422 is output
B
|
|
||||
| A | ||
| ||
| 5. CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION |
Turn the ignition switch off.
Check the brake pedal height and stop light switch assembly installation (Click here).
- OK:
- The brake pedal height and stop light switch assembly installation are normal.
|
|
||||
| OK | |
| 6. INSPECT STOP LIGHT SWITCH ASSEMBLY |
Remove the stop light switch assembly (Click here).
Inspect the stop light switch assembly (Click here).
- OK:
- The stop light switch assembly is normal.
|
|
||||
| OK | |
| 7. CHECK TERMINAL VOLTAGE (STP TERMINAL) |
Turn the ignition switch off.

Reinstall the stop light switch assembly (Click here).
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the B92 skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B92-35 (STP) - Body ground
Stop light switch assembly on (Brake pedal depressed)
8 to 14 V
B92-35 (STP) - Body ground
Stop light switch assembly off (Brake pedal released)
Below 1.5 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))
|
|
||||
| OK | ||
| ||
