2014-2019 Hiace · Service Manual BODY ELECTRICAL

Slide Door Lock Motor LH Circuit

Circuit diagnosis · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Dec 2016 from Jan 2017

DESCRIPTION

The instrument panel junction block assembly (body ECU) receives the rear left door lock/unlock request signal from the door control switch or door key cylinder. The instrument panel junction block assembly (body ECU) actives the door lock motor on rear door lock actuator assembly LH according to the signal.

WIRING DIAGRAM

E290539E04

INSPECTION PROCEDURE


1. CHECK VEHICLE TYPE
  1. Check the vehicle type.

    Result 
    Result
    Proceed to
    w/o Power Slide Door System
    A
    w/ Power Slide Door System
    B



B
Go to step 6
A


2. INSPECT REAR DOOR LOCK ACTUATOR ASSEMBLY LH
  1. Remove the rear door lock actuator assembly LH (Click here).

  1. Inspect the rear door lock actuator assembly LH (Click here).



NG
REPLACE REAR DOOR LOCK ACTUATOR ASSEMBLY LH (Click here)
OK


3. INSPECT SLIDE DOOR CONTROL FEMALE JUNCTION

  1. B111186E01
    Disconnect the slide door control female junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A - 1
    Always
    Below 1 Ω
    E - 2
    Always
    Below 1 Ω



NG
REPLACE SLIDE DOOR CONTROL FEMALE JUNCTION
OK


4. INSPECT SLIDE DOOR CONTROL MALE JUNCTION

  1. B102899E01
    Remove the slide door control male junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A - 2
    Always
    Below 1 Ω
    E - 5
    Always
    Below 1 Ω



NG
REPLACE SLIDE DOOR CONTROL MALE JUNCTION
OK


5. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY [BODY ECU] - REAR DOOR LOCK ACTUATOR ASSEMBLY LH)
  1. Disconnect the 13E instrument panel junction block assembly (body ECU) connector.

  1. Disconnect the p5 rear door lock actuator assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    13E-26 (ACT+) - p5-1
    Always
    Below 1 Ω
    13E-27 (ACT-) - p5-2
    Always
    Below 1 Ω
    13E-26 (ACT+) or p5-1 - Body ground
    Always
    10 kΩ or higher
    13E-27 (ACT-) or p5-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

6. INSPECT REAR DOOR LOCK ACTUATOR ASSEMBLY LH
  1. Remove the rear door lock actuator assembly LH (Click here).

  1. Inspect the rear door lock actuator assembly LH (Click here).



NG
REPLACE REAR DOOR LOCK ACTUATOR ASSEMBLY LH (Click here)
OK


7. CHECK NO. 2 REAR DOOR WIRE

  1. B365974E01
    Disconnect the A and B No. 2 rear door wire connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-4 -B-18
    Always
    Below 1 Ω
    A-5 - B-12
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    No. 2 Rear Door Wire
    (to Instrument panel junction block Assembly [Body ECU])
    *b
    No. 2 Rear Door Wire
    (to Rear Door Lock Actuator Assembly LH)



NG
REPLACE NO. 2 REAR DOOR WIRE
OK


8. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY [BODY ECU] - REAR DOOR LOCK ACTUATOR ASSEMBLY LH)
  1. Disconnect the 13E instrument panel junction block assembly (body ECU) connector.

  1. Disconnect the p5 rear door lock actuator assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    13E-26 (ACT+) - p5-2
    Always
    Below 1 Ω
    13E-27 (ACT-) - p5-3
    Always
    Below 1 Ω
    13E-26 (ACT+) or p5-2 - Body ground
    Always
    10 kΩ or higher
    13E-27 (ACT-) or p5-3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Slide Door Lock Motor LH Circuit (Dec 2015 – Dec 2016)Slide Door Lock Motor RH Circuit (Oct 2014 – Dec 2014) →