P2742 Transmission Fluid Temperature Sensor "B" Circuit Low Input
Diagnostic trouble codes · Vehicles built Apr 2016 – Dec 2016
Also covers:
- P2743 Transmission Fluid Temperature Sensor "B" Circuit High Input
Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
DESCRIPTION
The No. 2 ATF temperature sensor is installed in the transmission valve body assembly.If the ECM detects an abnormally high ATF temperature near this sensor, it illuminates the warning light.
- HINT:
- The temperature of ATF easily rises when towing, climbing hills, in traffic, etc.
- If the No. 2 ATF temperature sensor becomes short-circuited, the signal that indicates that the ATF temperature is 150°C (302°F) or higher is input into the ECM.
- The temperature of ATF easily rises when towing, climbing hills, in traffic, etc.
| No. 2 ATF Temperature Sensor State |
Detection Condition |
Symptom |
Recovery Condition |
| Sensor is normal |
ATF temperature higher than 150°C (302°F) |
ATF temperature warning indicator remains on |
ATF temperature below 135°C (275°F)*1 |
| ATF temperature higher than 130°C (266°F) |
Shift point too high |
ATF temperature below 110°C (230°F) |
|
| Sensor is short-circuited |
Any conditions |
Shift point too high |
Symptoms still occur |
| Engine coolant temperature higher than 95°C (203°F) |
Lock-up at 3rd gear*2 |
Symptoms still occur |
- HINT:
- *1: When ATF temperature is in the normal range, it decreases to below 135°C (275°F) within 5 minutes with the shift lever in P or N in an idling state.
- *2: When ATF temperature is normal, transmission lock-up occurs in 4th, 5th and 6th gear with the shift lever in D or the S6 range, in 4th or 5th gear with the shift lever in the S5 range, and 4th gear with the shift lever in the S4 range.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| P2742 |
No. 2 ATF temperature sensor resistance is below 25 Ω for 0.5 seconds or more (1 trip detection logic). |
|
| P2743 |
No. 2 ATF temperature sensor resistance is higher than 156 kΩ for 0.5 seconds or more and either condition is met (1 trip detection logic): (A) 15 minutes or more have elapsed after the engine start when the engine coolant temperature or intake air temperature is -29.375°C (-20.875°F) or less. (B) 10 seconds or more have elapsed after the engine start when the engine coolant temperature and intake air temperature are higher than -29.375°C (-20.875°F). |
|
MONITOR DESCRIPTION
The No. 2 ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects an open or short in the No. 2 ATF temperature sensor circuit. If the resistance value of the No. 2 ATF temperature sensor is below 25 Ω*1 or higher than 156 kΩ*2, the ECM interprets this as a fault in the No. 2 ATF temperature sensor or wiring. The ECM stores the DTC.*1: 150°C (302°F) or higher is indicated regardless of the actual ATF temperature.
*2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.
- HINT:
- The ATF temperature can be checked on the GTS display.
WIRING DIAGRAM
Refer to DTC P0712 (Click here).INSPECTION PROCEDURE
- NOTICE:
- Perform registration and/or initialization when parts related to the automatic transmission are replaced (Click here).
| DATA LIST |
- HINT:
- Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the GTS, read the Data List.
Engine and ECT Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
A/T Oil Temperature 2
No. 2 ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 150°C (302°F)
- Approx. 80°C (176°F): After stall test
- Equal to ambient temperature when cold soak
If the value -40°C (-40°F) or 150°C (302°F), No. 2 ATF temperature sensor circuit is open or shorted.
- HINT:
- When DTC P2742 is output and the GTS indicates 150°C (302°F) or higher, there is a short circuit.
- When DTC P2743 is output and the GTS indicates -40°C (-40°F), there is an open circuit.
Check the temperature displayed on the GTS in order to check if a malfunction exists.
- When DTC P2742 is output and the GTS indicates 150°C (302°F) or higher, there is a short circuit.
Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
150°C (302°F) or higher
Short circuit
- Approx. 80°C (176°F): After stall test
| 1. INSPECT NO. 2 ATF TEMPERATURE SENSOR (TRANSMISSION WIRE) |
Disconnect the transmission wire connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
5 (OT2+) - 6 (OT2-)
Always
25 Ω to 156 kΩ
5 (OT2+) - Body ground
Always
10 kΩ or higher
6 (OT2-) - Body ground
Always
10 kΩ or higher
- HINT:
- If the resistance is out of the specified range at any of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.
ATF Temperature
Specified Condition
10°C (50°F)
5 to 8 kΩ
25°C (77°F)
2.5 to 4.5 kΩ
110°C (230°F)
0.22 to 0.28 kΩ
| *a |
Component without harness connected (Transmission Wire) |
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM) |
Disconnect the ECM connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D116-85 (THO2) - D116-128 (ETHO)
Always
25 Ω to 156 kΩ
D116-85 (THO2) - Body ground
Always
10 kΩ or higher
D116-128 (ETHO) - Body ground
Always
10 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to ECM)
|
|
||||
| OK | ||
| ||
