P2440 Secondary Air Injection System Switching Valve Stuck Open Bank1
Diagnostic trouble codes · Vehicles built Jan 2015 – Mar 2016
Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
Refer to DTC P2431 (Click here).| DTC No. |
DTC Detection Condition |
Trouble Area |
| P2440 |
Air pressure sensor detects pulsation of exhaust gas despite ECM commanding Air Switching Valve to close, while engine running (1 trip detection logic) |
|
- HINT:
- Air switching valve normal operation:
- When the Air Switching Valve is open, exhaust gas pulsation occurs in the secondary air passage.
- When the Air Switching Valve is closed, exhaust gas pulsation does not occur in the secondary air passage.
MONITOR DESCRIPTION
Air Switching Valve of the Secondary Air Injection system.If either of the following conditions occurs, the ECM interprets it as a malfunction of the secondary Air Injection system, and illuminates the MIL and stores a DTC:
- Exhaust gas pulsation is detected by the air pressure sensor despite the ECM commanding the Air Switching Valve to close.
- Exhaust gas pulsation is not detected by the air pressure sensor despite the ECM commanding the Air Switching Valve to open.
MONITOR STRATEGY
| Required Sensors/Components |
Air pressure sensor |
| Frequency of Operation |
Once per drive cycle |
TYPICAL MALFUNCTION THRESHOLDS
| P2440 AIR valve is stuck open |
- |
| One of the following conditions is met |
A or B |
| A: Cumulative pressure pulsation during Secondary Air Injection OFF (Case 1) |
10 kPa (75.01 mmHg) or higher |
| B: Cumulative pressure pulsation (Case 2) |
80 kPa (600.05 mmHg) or higher |
- HINT:
- Refer to "Data List / Active Test" [Air Pump Pressure (Absolute) and Air Pump Pulsation Pressure] (Click here).
CONFIRMATION DRIVING PATTERN
- NOTICE:
- This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds.
Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR).
If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.
- Performing the Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
- When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
- Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
- This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds.
- Start the engine and warm it up.
- Turn the ignition switch off.
- Connect the GTS to the DLC3.
- Turn the ignition switch to ON.
- Turn the GTS on.
- Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
- Turn the ignition switch off and wait for at least 30 seconds.
- Turn the ignition switch to ON and turn the GTS on.
- Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
- Start the engine after the GTS initialization is finished.
- Perform the System Check operation by pressing Next.
- Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.
- Check for pending DTCs.
- HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- If a pending DTC is output, the system is malfunctioning.
- After the "Air injection check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
- Input the DTC: P2440.
- Check the DTC judgment result.
GTS Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
N/A
- Unable to perform DTC judgment
- Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
- HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows NORMAL, the system is normal.
- DTC judgment completed
- Turn the ignition switch off.
WIRING DIAGRAM
Refer to the following pages.- Secondary air injection system air pressure sensor circuit (Click here).
- Secondary air injection system air switching valve circuit (Click here).
INSPECTION PROCEDURE
- HINT:
- By using the GTS to perform the Secondary Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, Pending Codes also can be checked by performing Utility / Secondary Air Injection Check / Automatic Mode after the repair.
- Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- By using the GTS to perform the Secondary Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, Pending Codes also can be checked by performing Utility / Secondary Air Injection Check / Automatic Mode after the repair.
| 1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO SECONDARY AIR INJECTION SYSTEM DTCS) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
Result Result
Proceed to
DTC P2440 is output
A
DTC P2440 and P0412 are output
B
DTC P2440 and other DTCs (except P0412) are output
C
|
|
||||
|
|
||||
| A | |
| 2. PERFORM ACTIVE TEST USING GTS (SECONDARY AIR INJECTION SYSTEM OPERATION) |
![]() ![]() |
Perform a visual check
Start the engine and warm it up.
Turn the ignition switch off.
Disconnect the air hose No. 6.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.
- HINT:
- When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
Start the engine.
Perform the secondary air injection system intrusive operation while the engine is idling.
Place your hand near the air switching valve port and check that the exhaust gas pressure pulsates when the ASV is turned on.
- CAUTION:
- To avoid the danger of being burned by the exhaust gas, bring your hand close to the valve port slowly.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: CLOSE.
Check that the exhaust gas does not pulsate when the ASV is turned off.
Turn the ignition switch off.
- NOTICE:
- This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
While Secondary Air Injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (Wait or Error).
If an Error is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.
- Performing the Secondary Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
- When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
- Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
- This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
- OK:
Air Pump Operation
ASV Operation
Exhaust Gas Pulsation
ON
OFF
Not detected
ON
ON
Detected
Reconnect the air hose No. 6.
Other inspection method:The air switching valve operation can be confirmed by checking the cumulative pressure pulsation* provided in the System Check.Perform System Check operation under Manual Mode. *: The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the secondary air injection system.
Start the engine and warm it up.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN and AIR PUMP: OFF, ASV: CLOSE.
Start the engine after the GTS initialization is finished.
Perform the secondary air injection system intrusive operation while the engine is idling.
Check that the air-fuel ratio and pressure in the secondary air injection system passage (PULSATION) displayed on the GTS, indicate the conditions shown in the table below.
Turn the ignition switch off.
- Standard:
Secondary Air Injection System Operation
Pulsation Condition
(ECM Calculation)
Air-Fuel Ratio
(Reference)
AIR PUMP: ON, ASV: OPEN
10 kPa or more
18 or more
AIR PUMP: OFF, ASV: CLOSE
Less than 10 kPa
Approximately 14.5
(around stoichiometric air-fuel ratio)
Result Result
Proceed to
NG
A
OK
B
- HINT:
- REFERENCE:
|
|
||||
| A | |
| 3. INSPECT INTAKE PIPE NO. 4 (BLOCKAGES AND LEAKAGES) |
![]() ![]() |
Check that the intake pipe No. 4 is securely connected to both the exhaust manifold and the air switching valve
Inspect the intake pipe No. 4 for blockages and damage.
Text in Illustration *1
Intake Pipe No. 4
- OK:
- No blockages or damage on intake pipe No. 4.
|
|
||||
| OK | |
| 4. INSPECT AIR SWITCHING VALVE ASSEMBLY (AIR SWITCHING VALVE OPERATION) |
Inspect the air switching valve assembly (Click here).
|
|
||||
| OK | |
| 5. INSPECT AIR INJECTION CONTROL DRIVER (POWER SOURCE OF AIR INJECTION CONTROL DRIVER) |
![]() ![]() |
Disconnect the air injection control driver connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
B14-1 (BATT) - Body ground
Always
11 to 14 V (near battery voltage)
B12-5 (+B) - Body ground
Ignition Switch ON
11 to 14 V (near battery voltage)
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B12-1 (E) - Body ground
Always
Below 1 Ω
Text in Illustration *a
Front view of wire harness connector
(to Air Injection Control Driver)
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER) |
Disconnect the ECM connector.
Disconnect the air injection control driver connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B94-21 (AIRV) - B12-3 (SIV)
Always
Below 1 Ω
B94-21 (AIRV) or B12-3 (SIV) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 7. PERFORM ACTIVE TEST USING GTS |
Disconnect the air injection control driver connector.
Connect terminals DI and SIV of the wire harness connector for the air injection control driver.

| *1 |
Air Injection Control Driver |
| *2 |
ECM |
| *a |
Front view of wire harness connector (to Air Injection Control Driver) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.
- HINT:
- When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
Start the engine.
Perform the secondary air injection system intrusive operation while the engine is idling.
Measure the voltage between the SIV and E terminals of the ECM connector when the secondary air injection system is on and off.
Turn the ignition switch off.
- NOTICE:
- Do not perform the System Check operation repetitively. It may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.
- When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
- Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
- Do not perform the System Check operation repetitively. It may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B12-3 (SIV) - B12-1 (E)
AIR PUMP: ON, ASV: OPEN
0.5 to 2 V
AIR PUMP: OFF, ASV: CLOSE
11 to 14 V
Connect terminals DI and SIP of the wire harness connector for the air injection control driver.

| *1 |
Air Injection Control Driver |
| *2 |
ECM |
| *a |
Front view of wire harness connector (to Air Injection Control Driver) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.
- HINT:
- When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
Start the engine.
Perform the secondary air injection system intrusive operation while the engine is idling.
Measure the voltage between the SIP and E terminals of the ECM connector when the secondary air injection system is on and off.
Turn the ignition switch off.
- NOTICE:
- Do not perform the System Check operation repetitively. It may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.
- When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
- Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
- Do not perform the System Check operation repetitively. It may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B12-4 (SIP) - B12-1 (E)
AIR PUMP: ON, ASV: OPEN
0.5 to 2 V
AIR PUMP: OFF, ASV: CLOSE
11 to 14 V
|
|
||||
| OK | |
| 8. REPLACE AIR INJECTION CONTROL DRIVER |
Replace the air injection control driver.
| NEXT | |
| 9. CHECK WHETHER DTC OUTPUT RECURS (DTC P2440) |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear DTCs (if stored) (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Enter the following menus: Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
Start the engine after the GTS initialization is finished.
Perform the System Check operation by pressing Next.
After operating the secondary air injection system, perform the following to confirm the secondary air injection system pending codes: Press the Exit button.
Check pending DTCs.
Turn the ignition switch off.
- OK:
- No pending DTC output.
- NOTICE:
- When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
- Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
- When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
|
|
||||
| OK | ||
| ||
| 10. INSPECT VACUUM HOSES (AIR SWITCHING VALVE - AIR PRESSURE SENSOR) |
- OK:
- No blockage and no deformation in vacuum hose.
|
|
||||
| OK | |
| 11. INSPECT AIR PRESSURE SENSOR |
Connect a pressure gauge to the air pressure sensor as shown in the illustration.

Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Air Pump Pressure (Absolute).
Check that the pressure displayed on the GTS fluctuates when applying pressure to the air pressure sensor with the pressure gauge.
- OK:
- Pressure fluctuates in response to pressure applied with pressure gauge.
- HINT:
- The GTS displays the air pump pressure (Air Pump Pressure (Absolute)) as absolute pressure.
|
|
||||
| OK | ||
| ||



