2014-2019 Hiace · Service Manual ENGINE

P0335 Crankshaft Position Sensor "A" Circuit

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

DESCRIPTION

The crankshaft position sensor system consists of a crank angle sensor plate and Magneto Resistance Element (MRE) type sensor. The crank angle sensor plate has 34 teeth at 10° intervals (2 teeth are missing for detecting top dead center), and is installed on the crankshaft. The crankshaft position sensor generates 34 signals per crankshaft revolution. The ECM uses the NE signal to detect the crankshaft position and engine speed.
P0335 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Crank or start engine
Either of the following conditions is met (1 trip detection logic):
  1. No crankshaft position sensor signal to the ECM while cranking.
  2. No crankshaft position sensor signal to the ECM while engine running.
  1. Crankshaft position sensor
  2. Crankshaft (crank angle sensor plate)
  3. ECM
P0339 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Engine running at 1000 rpm or more with vehicle stationary
Under conditions (a), (b) and (c), no crankshaft position sensor signal is sent to the ECM for 0.05 seconds or more (1 trip detection logic):
  1. (a) Engine speed is 1000 rpm or more.
  2. (b) Starter signal is off.
  3. (c) 3 seconds or more have elapsed since the starter signal switched from on to off.
  1. Crankshaft position sensor
  2. Crankshaft (crank angle sensor plate)
  3. ECM
Related Data List 
DTC No.
Data List
P0335
P0339
Engine Speed

HINT:
  1. If DTC P0335 and/or P0339 is stored, the following symptoms may appear:
    1. Difficulty starting
    2. Misfire
    3. Combustion noise
    4. Black smoke
    5. White smoke
    6. Lack of power

  1. A340471E03
    Reference: Inspection using an oscilloscope.
    The correct waveform is as shown.
    ECM Terminal Name
    Between G2+ and G2-
    Between NE+ and NE-
    Tester Range
    2 V/DIV., 20 msec./DIV.
    Condition
    Idling with warm engine


MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the crankshaft revolving, the ECM interprets this as a malfunction of the sensor.

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.
  2. The engine speed can be checked by using the GTS. To perform the check, follow the procedures below:
    1. Connect the GTS to the DLC3.
    2. Start the engine.
    3. Turn the GTS on.
    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Engine Speed.
      The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor.
      Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.
  3. Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK ENGINE
  1. Check the engine cranking condition.

    Result:
    Result
    Proceed to
    Cranking is OK.
    A
    Does not crank at all*
    B

    *: When the engine cannot crank, there may be a malfunction in the starter assembly.



B
GO TO PROBLEM SYMPTOMS TABLE (ENGINE DOES NOT CRANK (DOES NOT START)) (Click here)
A


2. READ VALUE USING GTS (ENGINE SPEED)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Engine Speed.

  1. Start the engine.

  1. Read the values displayed on the GTS while the engine is running.

    Standard:
    Correct values are displayed.

    HINT:
    1. To check the engine speed change, display the graph on the GTS.
    2. If the engine does not start, check the engine speed while cranking.
    3. If the engine speed indicated on the GTS remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.



NG
Go to step 4
OK


3. CHECK WHETHER DTC OUTPUT RECURS (DTC P0335 AND/OR P0339)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the engine switch off and wait for at least 30 seconds or more.

  1. Start the engine.

  1. Turn the GTS on.

  1. Idle the engine for 20 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    DTC P0335 and/or P0339 is output
    A
    DTC is not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


4. CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)

  1. A316078E03
    Check the crankshaft position sensor installation condition.

    OK:
    Crankshaft position sensor is installed correctly.

    Text in Illustration 
    *a
    Clearance



NG
Go to step 8
OK


5. INSPECT CRANKSHAFT (TEETH OF SENSOR PLATE)
  1. Inspect the teeth of the crank angle sensor plate.

    OK:
    Crank angle sensor plate does not have any cranks or deformation.



NG
Go to step 7
OK


6. REPLACE CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).



NEXT
Go to step 9
7. REPLACE CRANKSHAFT
  1. Replace the crankshaft (Click here).



NEXT
Go to step 9
8. SECURELY REINSTALL CRANK POSITION SENSOR
  1. Securely reinstall the crankshaft position sensor (Click here).



NEXT
Go to step 9
9. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Start the engine and run it at 1000 rpm or higher for 5 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    OK:
    DTC is not output again.



NG
REPLACE ECM (Click here)
OK

END


← P0301 Cylinder 1 Misfire Detected (+ P0302, P0303, P0304) (from Jan 2017)P0337 Crankshaft Position Sensor "A" Circuit Low Input (+ P0338) (from Jan 2017) →