2014-2019 Hiace · Service Manual ENGINE

P0337 Crankshaft Position Sensor "A" Circuit Low Input

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

DESCRIPTION

Refer to DTC P0335 (Click here).
P0337 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 4 seconds or more
Output voltage of crankshaft position sensor is less than 0.3 V for 4 seconds.
(1 trip detection logic)
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. ECM
P0338 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 4 seconds or more
Output voltage of crankshaft position sensor is higher than 4.7 V for 4 seconds.
(1 trip detection logic)
  1. Crankshaft position sensor
  2. Crankshaft (crank angle sensor plate)
  3. ECM

HINT:
  1. If DTC P0337 or P0338 is stored, the following symptoms may appear:
    1. Difficulty starting
    2. Misfire
    3. Combustion noise
    4. Black smoke
    5. White smoke
    6. Lack of power

  1. A340471E03
    Reference: Inspection using an oscilloscope.
    The correct waveform is as shown.
    ECM Terminal Name
    Between G2+ and G2-
    Between NE+ and NE-
    Tester Range
    2 V/DIV., 20 msec./DIV.
    Condition
    Idling with warm engine


MONITOR DESCRIPTION

When the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V, the ECM stores a DTC.

WIRING DIAGRAM

A348539E05

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK DTC OUTPUT
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Disconnect the crankshaft position sensor connector.

  1. Turn the ignition switch to ON for 4 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


Result:
Result
Proceed to
DTC does not change
A
DTC changes
B



B
Go to step 5
A


2. CHECK ECM (CRANKSHAFT POSITION SENSOR VOLTAGE)

  1. A376492E05
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D118-3 (VC) - D118-2 (NE-)
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Crankshaft Position Sensor)



NG
Go to step 7
OK


3. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the crankshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D118-1 (NE+) - D134-76 (NE+)
    Always
    Below 1 Ω
    D118-2 (NE-) - D134-109 (NE-)
    Always
    Below 1 Ω
    D118-1 (NE+) or D134-76 (NE+) - Body ground and other terminals
    Always
    10 kΩ or higher
    D118-2 (NE-) or D134-109 (NE-) - Body ground and other terminals
    Always
    10 kΩ or higher

  1. Reconnect the crankshaft position sensor connector.



NG
Go to step 6
OK


4. CHECK ECM (CHECK RESISTANCE)

  1. A376492E06
    Disconnect the crankshaft position sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D118-3 (VC) - D118-1 (NE+)
    Ignition switch off
    No short or no open circuit
    D118-1 (NE+) - D118-2 (NE-)
    Ignition switch off
    No short or no open circuit

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Crankshaft Position Sensor)

  1. Reconnect the crankshaft position sensor connector.



NG
Go to step 7
OK


5. REPLACE CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).



NEXT
Go to step 8
6. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.



NEXT
Go to step 8
7. REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


8. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Turn the ignition switch to ON for 4 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output.


NEXT

END


← P0335 Crankshaft Position Sensor "A" Circuit (+ P0339) (from Jan 2017)P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor) (+ P0343) (from Jan 2017) →