2014-2019 Hiace · Service Manual ENGINE

P0405 Exhaust Gas Recirculation Sensor "A" Circuit Low

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The EGR valve position sensor is mounted on the EGR valve and is used for detecting the lift amount of the valve. The lift amount detected by the sensor is provided to the ECM as feedback. The ECM then regulates the lift amount of the valve in accordance with engine running conditions.
P0405 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 5 seconds
EGR valve position sensor output voltage is below 0.1 V for more than 5 seconds (1 trip detection logic).
  1. Open or short in EGR valve position sensor circuit
  2. Electric EGR control valve assembly (EGR valve position sensor)
  3. ECM
P0406 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 5 seconds
EGR valve position sensor output voltage is more than 4.9 V for higher than 5 seconds (1 trip detection logic).
  1. Open or short in EGR valve position sensor circuit
  2. Electric EGR control valve assembly (EGR valve position sensor)
  3. ECM

MONITOR DESCRIPTION

When the output voltage of the EGR valve position sensor deviates from the normal operating range of 0.1 to 4.9 V for more than 5 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

WIRING DIAGRAM

A221592E03

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK TERMINAL VOLTAGE (EGR VALVE POSITION SENSOR CONNECTOR)

  1. A148945E09
    Disconnect the EGR valve position sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D52-1 (VC) - D52-2 (E2)
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to EGR Valve Position Sensor)

  1. Reconnect the electric vacuum regulating valve assembly connector.



NG
Go to step 3
OK


2. INSPECT EGR VALVE POSITION SENSOR
  1. Inspect the EGR valve position sensor (Click here).



NG
Go to step 5
OK


3. CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)
  1. Disconnect the EGR valve position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D52-1 (VC) - D98-75 (VC)
    Always
    Below 1 Ω
    D52-3 (EGLS) - D98-118 (EGLS)
    Always
    Below 1 Ω
    D52-2 (E2) - D98-92 (EEGL)
    Always
    Below 1 Ω
    D52-1 (VC) or D98-75 (VC) - Body ground
    Always
    10 kΩ or higher
    D52-3 (EGLS) or D98-118 (EGLS) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the electric vacuum regulating valve assembly connector.

  1. Reconnect the ECM connector.



NG
Go to step 6
OK


4. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 7
5. REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
  1. Replace the electric EGR control valve assembly (Click here).



NEXT
Go to step 7
6. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch to ON for 5 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0405 Exhaust Gas Recirculation Sensor "A" Circuit Low (+ P0406) (Apr 2016 – Dec 2016)P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance (Oct 2014 – Dec 2014) →