VC Output Circuit
Circuit diagnosis · Vehicles built from Jan 2017
Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
DESCRIPTION
The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.

When the VC circuit is short-circuited, the microprocessor in the ECM and the sensors that are supplied with power through the VC circuit are inactivated because power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.
- HINT:
- Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.
WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. CHECK MIL |
Check that the Malfunction Indicator Lamp (MIL) lights up when the ignition switch is turned to ON.
- OK:
- MIL lights up.
|
|
||||
| OK | ||
| ||
| 2. CHECK COMMUNICATION BETWEEN GTS AND ECM |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
Result Result
Proceed to
Communication is not possible
A
Communication is possible
B
|
|
||||
| A | |
| 3. CHECK MIL (THROTTLE POSITION SENSOR) |
Disconnect the throttle body assembly connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL does not illuminate
A
MIL illuminates
B
- HINT:
- Perform "Inspection After Repair" after cleaning the throttle body (Click here).
|
|
||||
| A | |
| 4. CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR) |
Disconnect the accelerator pedal position sensor connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL does not illuminate (w/ air pressure sensor)
A
MIL does not illuminate (w/o air pressure sensor)
B
MIL illuminates
C
|
|
||||
|
|
||||
| A | |
| 5. CHECK MIL (AIR PRESSURE SENSOR) |
Disconnect the air pressure sensor connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL does not illuminate
A
MIL illuminates
B
|
|
||||
| A | |
| 6. CHECK MIL (CAMSHAFT POSITION SENSOR (FOR INTAKE SIDE)) |
Disconnect the camshaft position sensor (for intake side) connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL does not illuminate
A
MIL illuminates
B
|
|
||||
| A | |
| 7. CHECK MIL (CAMSHAFT POSITION SENSOR (FOR EXHAUST SIDE)) |
Disconnect the camshaft position sensor (for exhaust side) connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL does not illuminate
A
MIL illuminates
B
|
|
||||
| A | |
| 8. CHECK MIL (BATTERY CURRENT SENSOR) |
Disconnect the battery current sensor connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL does not illuminate
A
MIL illuminates
B
|
|
||||
| A | |
| 9. CHECK HARNESS AND CONNECTOR |
Disconnect the throttle body with motor assembly connector.
Disconnect the accelerator pedal position sensor connector.
Disconnect the air pressure sensor connector. (with air pressure sensor)
Disconnect the camshaft position sensor (for intake side) connector.
Disconnect the camshaft position sensor (for exhaust side) connector.
Disconnect the battery current sensor connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D116-134 (VCTA) - Body ground
Always
10 kΩ or higher
B94-49 (VCPA) - Body ground
Always
10 kΩ or higher
B94-52 (VCP2) - Body ground
Always
10 kΩ or higher
D116-129 (VCAI) - Body ground
Always
10 kΩ or higher
D116-116 (VCV1) - Body ground
Always
10 kΩ or higher
D116-111 (VCE1) - Body ground
Always
10 kΩ or higher
D116-117 (VCIB) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
