Home › ENGINE › 2TR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM (w/ Secondary Air Injection System)
Fuel Pump Control Circuit
Circuit diagnosis · Vehicles built from Jan 2017
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017
DESCRIPTION
When the engine is cranked, the starter (ST) relay drive signal output from the ignition switch is input into the STA terminal of the ECM, and the NE signal generated by the crankshaft position sensor is input into the NE+ terminal. The ECM determines that the engine is cranked, and turns transistor in the ECM internal circuit on. Current flows to the circuit opening (C/OPN) relay by turning transistor on. Then, the fuel pump operates. While the NE signal is input into the ECM and the engine is running, the ECM turns transistor on continuously. WIRING DIAGRAM
INSPECTION PROCEDURE
NOTICE:
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check whether the fuel pump operating sound occurs when performing the Active Test on the intelligent tester.
OK:
Fuel pump operating sound occurs.
NG
OK
2. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the result when the ignition switch is turned to ON and START.
OK:
Ignition Switch Position
Starter Signal
ON
OFF
START
ON
NG
REPAIR OR REPLACE STARTING SYSTEM
OK
3. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
Read the values displayed on the intelligent tester while cranking the engine.
OK:
Values are displayed continuously.
NG
REPAIR OR REPLACE CRANKSHAFT POSITION SENSOR CIRCUIT
OK
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here )
4. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
Disconnect the ECM connector.
Disconnect the No. 1 integration relay connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
B71-19 (FC) - 10A-3
Always
Below 1 Ω
B71-19 (FC) or 10A-3 - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
5. INSPECT NO. 1 INTEGRATION RELAY (C/OPN RELAY INPUT VOLTAGE)
Remove the No. 1 integration relay from the No. 1 engine room relay block.
Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
10A-2 - Body ground
Ignition switch off
Below 1 V
10A-4 - Body ground
10A-2 - Body ground
Ignition switch ON
11 to 14 V
10A-4 - Body ground
Engine cranking
Text in Illustration
*a
Component with harness connected (No. 1 Integration Relay)
NG
OK
6. CHECK HARNESS AND CONNECTOR (FUEL PUMP - NO. 1 INTEGRATION RELAY, BODY GROUND)
Remove the No. 1 integration relay from the No. 1 engine room relay block.
Disconnect the fuel pump connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
h2-4 - 10A-4
Always
Below 1 Ω
h2-5 - Body ground
Always
Below 1 Ω
h2-4 or 10A-4 - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
7. INSPECT FUEL PUMP
Inspect the fuel pump (Click here ).
NG
OK
8. INSPECT NO. 1 INTEGRATION RELAY (C/OPN)
Inspect the No. 1 integration relay (C/OPN) (Click here ).
NG
REPLACE NO. 1 INTEGRATION RELAY
OK
9. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - NO. 1 INTEGRATION RELAY, NO. 2 INTEGRATION RELAY)
Remove the No. 1 integration relay from the No. 1 engine room relay block.
Remove the No. 2 integration relay from the instrument panel relay block.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
12B-7 - 10A-2
Always
Below 1 Ω
10A-1 - 10A-8
Always
Below 1 Ω
12B-7 or 10A-2 - Body ground
Always
10 kΩ or higher
10A-1 or 10A-8 - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK