2014-2019 Hiace · Service Manual ENGINE

ECM Power Source Circuit

Circuit diagnosis · Vehicles built Apr 2016 – Dec 2016

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil of the No. 1 integration relay (EFI), closing the contacts and supplying power to terminals +B of the ECM.

WIRING DIAGRAM

A340542E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK NO. 1 INTEGRATION RELAY (POWER SOURCE)
A201293E09
  1. Remove the No. 1 integration relay from the No. 1 engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    10C-1 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 1 Integration Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - BATTERY)
OK


2. INSPECT NO. 1 INTEGRATION RELAY (EFI)
  1. Inspect the No. 1 integration relay (EFI) (Click here).



NG
REPLACE NO. 1 INTEGRATION RELAY
OK


3. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM, BODY GROUND)
  1. Remove the No. 1 integration relay from the No. 1 engine room relay block.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B94-46 (MREL) - 10A-6
    Always
    Below 1 Ω
    B94-2 (+B) - 10A-8
    Always
    Below 1 Ω
    B94-3 (+B2) - 10A-8
    Always
    Below 1 Ω
    10A-7 - Body ground
    Always
    Below 1 Ω
    B94-46 (MREL) or 10A-6 - Body ground
    Always
    10 kΩ or higher
    B94-2 (+B) or 10A-8 - Body ground
    Always
    10 kΩ or higher
    B94-3 (+B2) or 10A-8 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D116-59 (E1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT ECM (IGSW VOLTAGE)
A255690E76
  1. Disconnect the ECM connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B94-6 (IGSW) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
Go to step 6
OK

REPLACE ECM (Click here)

6. CHECK NO. 2 INTEGRATION RELAY (POWER SOURCE)
A299433E04
  1. Remove the No. 2 integration relay from the instrument panel relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    12A-1 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 2 Integration Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. INSPECT NO. 2 INTEGRATION RELAY (IG2)
  1. Inspect the No. 2 integration relay (IG2) (Click here).



NG
REPLACE NO. 2 INTEGRATION RELAY
OK


8. CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - IGNITION SWITCH, ECM, BODY GROUND)
  1. Disconnect the ECM connector.

  1. Disconnect the ignition switch connector.

  1. Remove the No. 2 integration relay from the instrument panel relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    12D-2 - H25-6 (IG2)
    Always
    Below 1 Ω
    12B-7 - B94-6 (IGSW)
    Always
    Below 1 Ω
    12E-4 - Body ground
    Always
    Below 1 Ω
    12D-2 or H25-6 (IG2) - Body ground
    Always
    10 kΩ or higher
    12B-7 or B94-6 (IGSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. INSPECT IGNITION SWITCH
  1. Inspect the ignition switch (Click here).



NG
REPLACE IGNITION SWITCH
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY)


← ECM Power Source Circuit (Jan 2015 – Mar 2016)ECM Power Source Circuit (from Jan 2017) →