2014-2019 Hiace · Service Manual BRAKE

ABS Warning Light Remains ON

Circuit diagnosis · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017

DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.
If any of the following is detected, the ABS warning light remains on:
  1. The skid control ECU (brake actuator assembly) connectors are disconnected from the skid control ECU (brake actuator assembly).
  2. There is a malfunction in the skid control ECU (brake actuator assembly) internal circuit.
  3. There is an open in the harness between the combination meter assembly and the skid control ECU (brake actuator assembly).
  4. The ABS control system is defective.

HINT:
In some cases, the GTS cannot be used when the skid control ECU (brake actuator assembly) is abnormal.


WIRING DIAGRAM

C324597E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check if CAN communication system DTCs are output (Click here).

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2. CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU (brake actuator assembly) connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY
OK


3. INSPECT BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V



NG
CHECK OR REPLACE CHARGING SYSTEM OR BATTERY
OK


4. CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
  1. Turn the ignition switch off.

  1. C117862E76
    Disconnect the B19 skid control ECU (brake actuator assembly) connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B19-25 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


5. CHECK HARNESS AND CONNECTOR (GND TERMINAL)
C117862E77
  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B19-2 (GND) - Body ground
    Always
    Below 1 Ω
    B19-24 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


6. READ VALUE USING GTS (ABS WARNING LIGHT)
  1. Reconnect the B19 skid control ECU (brake actuator assembly) connector.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. According to the display on the GTS, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ABS Warning Light
    ABS warning light / ON or OFF
    ON: Warning light on
    OFF: Warning light off
    -

  1. Check the GTS display condition of the ABS warning light.

    Result:
    Result
    Proceed to
    Display of the Data List remains OFF
    A
    Display of the Data List remains ON
    B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

INSPECT METER / GAUGE SYSTEM (Click here)


← ABS Warning Light Remains ON (Jan 2015 – Dec 2016)ABS Warning Light does not Come ON (Oct 2014 – Dec 2014) →