2014-2019 Hiace · Service Manual BRAKE

Slip Indicator Light Remains ON

Circuit diagnosis · Vehicles built Jan 2017 – Nov 2017

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.
The slip indicator light blinks during VSC and/or TRC operation.
If a malfunction is detected, the slip indicator light comes on to warn the driver (Click here).

WIRING DIAGRAM

C321579E01

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK CAN COMMUNICATION LINE
  1. Check if CAN communication system DTCs are output (Click here).

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
CHECK CAN COMMUNICATION SYSTEM (Click here)
A


2. CHECK BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU (brake actuator assembly) connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY
OK


3. INSPECT BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V


    HINT:
    Refer to the inspection procedures: 
    Item
    See page
    1KD-FTV
    Click here
    2KD-FTV
    Click here
    1TR-FE
    Click here
    2TR-FE (except Dual VVT-i)
    Click here
    2TR-FE (w/ Dual VVT-i)
    Click here



NG
CHECK OR REPLACE CHARGING SYSTEM OR BATTERY
OK


4. CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
  1. Turn the ignition switch off.

  1. C306843E08
    Disconnect the B92 skid control ECU (brake actuator assembly) connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B92-12 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


5. CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
C306843E03
  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B92-25 (GND1) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)
OK


6. READ VALUE USING GTS (SLIP INDICATOR LIGHT)
  1. Reconnect the B92 skid control ECU (brake actuator assembly) connector.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. According to the display on the GTS, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Slip Indicator Light
    Slip indicator light / ON or OFF
    ON: Indicator light on
    OFF: Indicator light off
    -

  1. Check the GTS display condition of the slip indicator light.

    Result:
    Result
    Proceed to
    Display of the Data List remains OFF
    A
    Display of the Data List remains ON
    B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

INSPECT METER / GAUGE SYSTEM (Click here)


← Slip Indicator Light Remains ON (Apr 2016 – Dec 2016)Slip Indicator Light Remains ON (from Dec 2017) →