2014-2019 Hiace · Service Manual ENGINE

P0046 Turbocharger / Supercharger Boost Control "A" Circuit Range / Performance

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

DESCRIPTION

These DTCs indicate that the DC motor of the turbocharger is malfunctioning. The ECM monitors the DC motor current to detect an open or short in the DC motor circuit. If the current meets certain criteria, the ECM stores a DTC and illuminates the MIL immediately.
The DC motor is used to operate the nozzle vane of the turbocharger. The nozzle vane opens and closes to change the velocity of exhaust emissions in order to control the turbo pressure. The ECM varies the duty ratio of the DC motor in accordance with the driving conditions.
If the nozzle vane is stuck closed (DC motor stuck off), drivability may deteriorate at wide open throttle. If the nozzle vane is stuck open (DC motor stuck on), drivability may deteriorate at intermediate throttle positions or the engine power may be insufficient.
P0046 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Maintain the Active Test "Activate the VN Turbo Open" at Open (VN turbo fully open) and OFF (normal control) for 65 seconds or more.
The difference between the target VN opening angle and the actual VN opening angle is 50% or greater for 65 seconds or more.
(1 trip detection logic)
  1. Turbocharger nozzle vane control actuator
  2. Turbocharger sub-assembly
  3. Turbocharger nozzle vane is stuck or movement is irregular
P0047 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
2 seconds after engine is started, race engine for 1 second
The DC motor duty ratio is 80% or more and the motor current is 0.5 A or less for 3 seconds or more (1 trip detection logic).
  1. Open in DC motor (turbocharger nozzle vane control actuator) circuit
  2. Turbocharger nozzle vane control actuator
  3. Turbocharger nozzle vane is stuck or movement is irregular
P0048 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
2 seconds after engine is started, race engine for 1 second
Overcurrent is detected 25 times or more (0.4 seconds or more) (1 trip detection logic).
  1. Short in DC motor (turbocharger nozzle vane control actuator) circuit
  2. Turbocharger nozzle vane control actuator
  3. Turbocharger nozzle vane is stuck or movement is irregular

HINT:
  1. If DTC P0046, P0047 and/or P0048 is stored due to the nozzle vane being stuck closed, the following symptom may appear:
    1. Vehicle surge when driving with full load
  2. If DTC P0046, P0047 and/or P0048 is stored due to the nozzle vane being stuck open, the following symptoms may appear:
    1. Lack of power
    2. Vehicle surge or hesitation under light or medium load


WIRING DIAGRAM

A348538E07

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0046, P0047 AND/OR P0048)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0046 is output
    A
    DTC P0047 and/or P0048 is output
    B
    DTC P0046, P0047 and/or P0048 and other DTCs are output
    C

    HINT:
    If codes other than P0046, P0047 and/or P0048 are output, perform troubleshooting for those DTCs first.



B
Go to step 5

C
GO TO DTC CHART (Click here)
A


2. INSPECT TURBOCHARGER NOZZLE VANE PLATE
  1. Remove the turbocharger sub-assembly (Click here).

  1. Inspect the turbocharger nozzle vane plate.

    1. Remove the e-washer from the turbocharger nozzle vane control actuator.

    2. A348999
      Move the turbocharger vane control rod sub-assembly and check that the turbocharger nozzle vane plate moves.

      Result:
      Result
      Proceed to
      Catches, but operates*
      OK
      Gets stuck and does not operate
      NG

      HINT:
      *: Check several times.



NG
Go to step 4
OK


3. REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR
  1. Replace the turbocharger nozzle vane control actuator (Click here).



NEXT
Go to step 10
4. REPLACE TURBOCHARGER SUB-ASSEMBLY
  1. Replace the turbocharger sub-assembly (Click here).



NEXT
Go to step 10
5. INSPECT TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR (DC MOTOR RESISTANCE)

  1. C217215
    Disconnect the DC motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1 to 100 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (DC Motor)

  1. Reconnect the DC motor connector.



NG
Go to step 8
OK


6. CHECK HARNESS AND CONNECTOR (DC MOTOR - ECM)
  1. Disconnect the DC motor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D65-2 (M+) - D134-19 (VNM+)
    Always
    Below 1 Ω
    D65-1 (M-) - D134-49 (VNM-)
    Always
    Below 1 Ω
    D65-2 (M+) or D134-19 (VNM+) - Body ground and other terminals
    Always
    10 kΩ or higher
    D65-1 (M-) or D134-49 (VNM-) - Body ground and other terminals
    Always
    10 kΩ or higher

  1. Reconnect the DC motor connector.

  1. Reconnect the ECM connector.



NG
Go to step 9
OK


7. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 10
8. REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR
  1. Replace the turbocharger nozzle vane control actuator (Click here).



NEXT
Go to step 10
9. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


10. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for 30 seconds or more.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VN Turbo Open.

  1. Maintain the Active Test "Activate the VN Turbo Open" at Open (VN turbo fully open) and OFF (normal control) for 65 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) (+ P0032) (from Jan 2017)P0069 Manifold Absolute Pressure - Barometric Pressure Correlation (from Jan 2017) →