2014-2019 Hiace · Service Manual BODY

2-2 Door Lock Pawl Switch Malfunction

Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017

DESCRIPTION

Code 2-2 is output when the power slide door lock assembly LH or power slide door lock assembly RH* (pawl switch) is malfunctioning.
DTC No.
DTC Detection Condition
Trouble Area
2-2
  1. During self-diagnostic mode 1, pawl switch ON/OFF signals are not output correctly when power slide door is operated
  1. Power slide door lock assembly LH
  2. Power slide door lock assembly RH*
  3. No. 2 rear door wire
  4. Rear door wire RH*
  5. Door control relay assembly
  6. Harness or connector
  1. *: for RH Side, w/ Power Slide Door

WIRING DIAGRAM

(Click here)

INSPECTION PROCEDURE


1. CLEAR DTC
  1. Clear the DTC (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTC (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output (for LH Side)
    B
    DTC is output (for RH Side, w/ Power Slide Door)
    C



B
Go to step 3

C
Go to step 6
A

USE SIMULATION METHOD TO CHECK (Click here)

3. INSPECT POWER SLIDE DOOR LOCK ASSEMBLY LH
  1. Remove the power slide door lock assembly LH (Click here).

  1. Inspect the power slide door lock assembly LH (Click here).



NG
REPLACE POWER SLIDE DOOR LOCK ASSEMBLY LH (Click here)
OK


4. INSPECT NO. 2 REAR DOOR WIRE

  1. B365974E01
    Disconnect the oq1 and po2 No. 2 rear door wire connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-7 - B-8
    Always
    Below 1 Ω
    A-10 - B-16
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    No. 2 Rear Door Wire
    (Door Control Relay Assembly Side)
    *b
    No. 2 Rear Door Wire
    (Power Slide Door Lock Assembly LH Side)



NG
REPLACE NO. 2 REAR DOOR WIRE (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (POWER SLIDE DOOR LOCK ASSEMBLY LH - DOOR CONTROL RELAY ASSEMBLY)
  1. Disconnect the p1 power slide door lock assembly LH connector.

  1. Disconnect the q4 door control relay assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    q4-18 (POL) - p1-9 (LSSR)
    Always
    Below 1 Ω
    q4-13 (OSG) - p1-8 (E2)
    Always
    Below 1 Ω
    q4-18 (POL) or p1-9 (LSSR) - Body ground
    Always
    10 kΩ or higher
    q4-13 (OSG) or p1-8 (E2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DOOR CONTROL RELAY ASSEMBLY (Click here)

6. INSPECT POWER SLIDE DOOR LOCK ASSEMBLY RH
  1. Remove the power slide door lock assembly RH (Click here).

  1. Inspect the power slide door lock assembly RH (Click here).



NG
REPLACE POWER SLIDE DOOR LOCK ASSEMBLY RH (Click here)
OK


7. INSPECT REAR DOOR WIRE RH

  1. B365974E01
    Disconnect the ci1 and fc1 rear door wire RH connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-7 - B-8
    Always
    Below 1 Ω
    A-10 - B-16
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Rear Door Wire RH
    (Door Control Relay Assembly Side)
    *b
    Rear Door Wire RH
    (Power Slide Door Lock Assembly RH Side)



NG
REPLACE REAR DOOR WIRE RH (Click here)
OK


8. CHECK HARNESS AND CONNECTOR (POWER SLIDE DOOR LOCK ASSEMBLY RH - DOOR CONTROL RELAY ASSEMBLY)
  1. Disconnect the f1 power slide door lock assembly RH connector

  1. Disconnect the I4 door control relay assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I4-18 (POL) - f1-9 (POL)
    Always
    Below 1 Ω
    I4-13 (OSG) - f1-8 (E1)
    Always
    Below 1 Ω
    I4-18 (POL) or f1-9 (POL) - Body ground
    Always
    10 kΩ or higher
    I4-13 (OSG) or f1-8 (E1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DOOR CONTROL RELAY ASSEMBLY (Click here)


← 2-1 Door Lock Half-latch Switch Malfunction (from Jan 2017)2-2 Door Lock Pawl Switch Malfunction (Jan 2015 – Dec 2016) →