Fuel Injector Circuit
Circuit diagnosis · Vehicles built from Apr 2016
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 from Apr 2016
DESCRIPTION
The fuel injectors are located on the cylinder head. They inject fuel into the cylinders based on the signals from the ECM.WIRING DIAGRAM
Refer to DTC P0300 (Click here).INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| 1. INSPECT FUEL INJECTOR ASSEMBLY (POWER SOURCE) |
 |
Disconnect the fuel injector connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
|
Switch Condition
|
Specified Condition
|
D24-1 - Body ground
|
Ignition switch ON
|
11 to 14 V
|
D25-1 - Body ground
|
Ignition switch ON
|
11 to 14 V
|
D26-1 - Body ground
|
Ignition switch ON
|
11 to 14 V
|
D27-1 - Body ground
|
Ignition switch ON
|
11 to 14 V
|
Text in Illustration
*a
|
Front view of wire harness connector (to Fuel Injector Assembly)
|
|
NG |
 |
|
|
|
| OK |
|
 |
|
| 2. INSPECT FUEL INJECTOR ASSEMBLY |
 |
Inspect the fuel injector assembly (Click here).
|
NG |
 |
|
|
|
| OK |
|
 |
|
| 3. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM) |
 |
Disconnect the fuel injector connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
D24-2 - D97-86 (#10)
|
Always
|
Below 1 Ω
|
D25-2 - D97-85 (#20)
|
Always
|
Below 1 Ω
|
D26-2 - D97-84 (#30)
|
Always
|
Below 1 Ω
|
D27-2 - D97-83 (#40)
|
Always
|
Below 1 Ω
|
D24-2 or D97-86 (#10) - Body ground
|
Always
|
10 kΩ or higher
|
D25-2 or D97-85 (#20) - Body ground
|
Always
|
10 kΩ or higher
|
D26-2 or D97-84 (#30) - Body ground
|
Always
|
10 kΩ or higher
|
D27-2 or D97-83 (#40) - Body ground
|
Always
|
10 kΩ or higher
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
|
| 4. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - NO. 1 INTEGRATION RELAY) |
 |
Disconnect the fuel injector connectors.
Remove the No. 1 integration relay from the No. 1 engine room relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
D24-1 - 10B-4
|
Always
|
Below 1 Ω
|
D25-1 - 10B-4
|
Always
|
Below 1 Ω
|
D26-1 - 10B-4
|
Always
|
Below 1 Ω
|
D27-1 - 10B-4
|
Always
|
Below 1 Ω
|
D24-1 or 10B-4 - Body ground
|
Always
|
10 kΩ or higher
|
D25-1 or 10B-4 - Body ground
|
Always
|
10 kΩ or higher
|
D26-1 or 10B-4 - Body ground
|
Always
|
10 kΩ or higher
|
D27-1 or 10B-4 - Body ground
|
Always
|
10 kΩ or higher
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 5. INSPECT NO. 1 INTEGRATION RELAY (INJ) |
 |
Inspect the No. 1 integration relay (INJ) (Click here).
|
NG |
 |
|
| REPLACE NO. 1 INTEGRATION RELAY |
|
|
| OK |
|
 |
|
| 6. CHECK NO. 1 INTEGRATION RELAY (POWER SOURCE) |
 |
Remove the No. 1 integration relay from the No. 1 engine room relay block.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
10B-1 - Body ground
|
Always
|
11 to 14 V
|
Text in Illustration
*a
|
Front view of wire harness connector (to No. 1 Integration Relay)
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - BATTERY) |
|
|
| OK |
|
 |
|
| 7. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND) |
 |
Remove the No. 1 integration relay from the No. 1 engine room relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
10B-3 - Body ground
|
Always
|
Below 1 Ω
|
Result
Result
|
Proceed to
|
OK (w/ Air Pressure Sensor)
|
A
|
OK (w/o Air Pressure Sensor)
|
B
|
NG
|
C
|
|
B |
 |
|
|
|
|
C |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| A |
|
 |
|
| 8. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - NO. 1 INTEGRATION RELAY) |
 |
Remove the No. 1 integration relay from the No. 1 engine room relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
10A-8 - 10B-2
|
Always
|
Below 1 Ω
|
10A-8 or 10B-2 - Body ground
|
Always
|
10 kΩ or higher
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
|
| 9. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - NO. 2 INTEGRATION RELAY) |
 |
Remove the No. 1 integration relay from the No. 1 engine room relay block.
Remove the No. 2 integration relay from the instrument panel relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
12B-7 - 10B-2
|
Always
|
Below 1 Ω
|
12B-7 or 10B-2 - Body ground
|
Always
|
10 kΩ or higher
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
|