2014-2019 Hiace · Service Manual BRAKE

C1436 Yaw Rate Sensor Malfunction

Diagnostic trouble codes · Vehicles built Jan 2015 – Mar 2016

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.
The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).
If there is trouble in the bus lines between the acceleration sensor (airbag sensor assembly) and the CAN communication system, DTC U0124 (Lost Communication with Lateral Acceleration Sensor Module) is set.
These DTCs are also output when calibration has not been completed.
DTC No.
DTC Detection Condition
Trouble Area
C1436
Either of the following is detected:
  1. With the vehicle stationary, the yaw rate and acceleration sensor output value is not 0 deg/s.
  2. Abnormal comparison value.
  1. Improper yaw rate sensor (Airbag sensor assembly) installation
  2. Yaw rate sensor (Airbag sensor assembly)

WIRING DIAGRAM

Refer to DTCs C1232, C1243 and C1245 (Click here).

INSPECTION PROCEDURE

NOTICE:
When replacing the yaw rate and acceleration sensor (airbag sensor assembly), perform zero point calibration and store system information (Click here).

HINT:
When U0124 and/or U0126 is output together with C1436, inspect and repair the trouble areas indicated by U0124 and/or U0126 first (Click here).


1. READ VALUE USING GTS (YAW RATE SENSOR)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. According to the display on the GTS, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Yaw Rate Sensor
    Yaw rate sensor / Min.: -128°/s, Max.: 127°/s
    Vehicle stopped: 0°/s
    Turning right: -128 to 0°/s
    Turning left: 0 to 127°/s
    -

  1. Check that the yaw rate sensor output value displayed on the GTS.

    Result:
    Result
    Proceed to
    NG (The yaw rate sensor (airbag sensor assembly) output value is 0 deg/s when the vehicle is stationary, but the value fluctuates when turning)
    A
    NG (The yaw rate sensor (airbag sensor assembly) output value is not 0 deg/s when the vehicle is stationary)
    B
    OK
    C

    NOTICE:
    Check the yaw rate and acceleration sensor signal after replacement (Click here).

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


2. CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
  1. Turn the ignition switch off.

  1. Check that the airbag sensor assembly has been installed properly (Click here).

    OK:
    The sensor should be tightened to the specified torque.
    The sensor should not be installed in a tilted position.

    NOTICE:
    Check the yaw rate and acceleration sensor signal after replacement (Click here).



NG
INSTALL AIRBAG SENSOR ASSEMBLY (Click here)
OK

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)


← C1434 Steering Angle Sensor Output Malfunction (from Dec 2017)C1436 Yaw Rate Sensor Malfunction (Apr 2016 – Dec 2016) →