2014-2019 Hiace · Service Manual COMMUNICATION SYSTEM

Skid Control ECU Communication Stop Mode

Circuit diagnosis · Vehicles built from Jan 2017

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

Detection Item
Symptom
Trouble Area
Skid Control ECU Communication Stop Mode
Either condition is met:
  1. "Skid Control (ABS/VSC/TRAC)" is not displayed on "Bus Check".
  2. "ABS and Traction Actuator (Skid Control ECU) Communication Stop Mode" in "DTC Combination Table" applies.
  1. Power source or inside brake actuator assembly (Skid Control ECU)
  2. Brake actuator assembly (Skid Control ECU) CAN branch wire or connector
  3. Brake actuator assembly (Skid Control ECU)
  1. For vehicles with an ABS.

WIRING DIAGRAM

C317022E01
C317022E02

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.

    CAUTION:
    For vehicles with an airbag system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR OPEN IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY CAN BRANCH WIRE)

  1. C317023E01
    Disconnect the brake actuator assembly (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ VSC:
    Tester Connection
    Switch Condition
    Specified Condition
    B92-22 (CANH) - B92-10 (CANL)
    Ignition switch off
    54 to 69 Ω
    w/o VSC:
    Tester Connection
    Switch Condition
    Specified Condition
    B19-6 (CANH) - B19-5 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *A
    w/ VSC
    *B
    w/o VSC
    *a
    Front view of wire harness connector
    (to Brake Actuator Assembly [Skid Control ECU])



NG
REPAIR OR REPLACE BRAKE ACTUATOR CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)
OK


3. CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BATTERY AND BODY GROUND)

  1. C317023E02
    Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ VSC:
    Tester Connection
    Condition
    Specified Condition
    B92-1 (GND2) - Body ground
    Always
    Below 1 Ω
    B92-25 (GND1) - Body ground
    Always
    Below 1 Ω
    w/o VSC:
    Tester Connection
    Condition
    Specified Condition
    B19-2 (GND) - Body ground
    Always
    Below 1 Ω
    B19-24 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    w/ VSC:
    Tester Connection
    Condition
    Specified Condition
    B92-13 (+BM) - Body ground
    Always
    11 to 14 V
    B92-38 (+BS) - Body ground
    Always
    11 to 14 V
    B92-12 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V
    w/o VSC:
    Tester Connection
    Condition
    Specified Condition
    B19-23 (+BM) - Body ground
    Always
    11 to 14 V
    B19-1 (+BS) - Body ground
    Always
    11 to 14 V
    B19-25 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*A
w/ VSC
*B
w/o VSC
*a
Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])
Result 
Result
Proceed to
OK (w/ VSC)
A
OK (w/o VSC)
B
NG
C


B
REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)


← Skid Control ECU Communication Stop Mode (Apr 2016 – Dec 2016)Air Conditioning Amplifier Communication Stop Mode (Oct 2014 – Dec 2014) →