P0489 Exhaust Gas Recirculation Control Circuit Low
Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014
Also covers:
- P0490 Exhaust Gas Recirculation Control Circuit High
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
DESCRIPTION
The EGR system recirculates exhaust gases in a way that suits every driving condition. The recirculated gas mixes with intake air. Therefore, the EGR system can slow combustion speed and keep the combustion temperature down. This helps reduce NOx emission.In order to increase EGR circulation efficiency, the ECM adjusts the lift amount of the EGR valve and the throttle valve angle.
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| 5 seconds after engine is started |
Open or short in electric vacuum regulating valve assembly circuit for 5 seconds or more (1 trip detection logic). |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| 5 seconds after engine is started |
Open or short in electric vacuum regulating valve assembly circuit for 5 seconds or more (1 trip detection logic). |
|
| DTC No. |
Data List |
| P0489 |
|
| P0490 |
WIRING DIAGRAM
Refer to DTC P0400 (Click here).INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
| 1. INSPECT ELECTRIC VACUUM REGULATING VALVE ASSEMBLY |
Inspect the electric vacuum regulating valve assembly (Click here).
|
|
||||
| OK | |
| 2. CHECK TERMINAL VOLTAGE (POWER SOURCE) |
Disconnect the electric vacuum regulating valve assembly connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D73-1 - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Electric Vacuum Regulating Valve Assembly)
Reconnect the electric vacuum regulating valve assembly connector.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (ELECTRIC VACUUM REGULATING VALVE ASSEMBLY - ECM) |
Disconnect the electric vacuum regulating valve assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D73-2 - D98-83 (EGR)
Always
Below 1 Ω
D73-2 or D98-83 (EGR) - Body ground
Always
10 kΩ or higher
Reconnect the electric vacuum regulating valve assembly connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 4. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 5. REPLACE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY |
Replace the electric vacuum regulating valve assembly (Click here).
|
|
||||
| 6. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
- HINT:
- If the voltage at the electric vacuum regulating valve assembly connector is not 11 to 14 V, repair or replace the harness and connector between the electric vacuum regulating valve assembly and the EFI MAIN relay (including the EFI No. 1 fuse).
| NEXT | |
| 7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the GTS to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Start the engine.
Idle the engine for 5 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| NEXT | ||
| ||
