Cruise Control Switch Circuit
Circuit diagnosis · Vehicles built Jan 2015 – Nov 2015
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
This circuit sends a signal to the ECM depending on the cruise control main switch condition. The battery supplies positive (+) battery voltage to the cruise control main switch. Terminal 23 (CCS)*1 or 40 (CCS)*2 of the ECM receives the voltage which varies according to the switch condition.- *1: for 1KD-FTV
- *2: for 2TR-FE
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. READ VALUE USING GTS (CRUISE CONTROL MAIN SWITCH) |
Using the GTS, read the Data List (Click here).
Cruise Control Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Main SW M-CPU
Cruise control main switch (Main CPU) / ON or OFF
ON: Cruise control main switch (ON-OFF) on
OFF: Cruise control main switch (ON-OFF) off
-
Cancel Switch
CANCEL switch signal / ON or OFF
ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch
-SET switch signal / ON or OFF
ON: -SET switch on
OFF: -SET switch off
-
RES/ACC Switch
+RES switch signal / ON or OFF
ON: +RES switch on
OFF: +RES switch off
-
- OK:
- The display is as specified in the normal condition column.
|
|
||||
| OK | ||
| ||
| 2. INSPECT CRUISE CONTROL MAIN SWITCH |
Remove the cruise control main switch (Click here).
Inspect the cruise control main switch (Click here).
|
|
||||
| OK | |
| 3. CHECK CRUISE CONTROL SWITCH WIRE |
Disconnect the A spiral cable sub-assembly connector.
Disconnect the B cruise control main switch wire connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A-3 (CCS) - B-3 (CCS)
Always
Below 1 Ω
A-4 (ECC) - B-1 (ECC)
Always
Below 1 Ω
A-3 (CCS) or B-3 (CCS) - Body ground
Always
10 kΩ or higher
A-4 (ECC) or B-1 (ECC) - Body ground
Always
10 kΩ or higher
| *a |
Front view of wire harness connector (to Spiral Cable Sub-assembly) |
| *b |
Front view of wire harness connector (to Cruise Control Main Switch) |
|
|
||||
| OK | |
| 4. INSPECT SPIRAL CABLE SUB-ASSEMBLY |
Remove the spiral cable sub-assembly (Click here).
Inspect the spiral cable sub-assembly (Click here).
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND) |
Disconnect the H77 spiral cable sub-assembly connector.
Disconnect the B72*1 or B71*2 ECM connector.
- *1: for 1KD-FTV
- *2: for 2TR-FE
- *1: for 1KD-FTV
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for 1KD-FTV Tester Connection
Condition
Specified Condition
H77-1 (CCS) - B72-23 (CCS)
Always
Below 1 Ω
H77-2 (ECC) - Body ground
H77-1 (CCS) or B72-23 (CCS) - Body ground
Always
10 kΩ or higher
for 2TR-FE Tester Connection
Condition
Specified Condition
H77-1 (CCS) - B71-40 (CCS)
Always
Below 1 Ω
H77-2 (ECC) - Body ground
H77-1 (CCS) or B71-40 (CCS) - Body ground
Always
10 kΩ or higher
| Result |
Proceed to |
| OK (for 1KD-FTV) |
A |
| OK (for 2TR-FE) |
B |
| NG |
C |
|
|
||||
|
|
||||
| A | ||
| ||
