2014-2019 Hiace · Service Manual CRUISE CONTROL SYSTEM

Cruise Control Switch Circuit

Circuit diagnosis · Vehicles built Apr 2016 – Dec 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

This circuit sends a signal to the ECM depending on the cruise control main switch condition. The battery supplies positive (+) battery voltage to the cruise control main switch. Terminal 23 (CCS)*1 or 40 (CCS)*2 of the ECM receives the voltage which varies according to the switch condition.
  1. *1: for 1KD-FTV
  2. *2: for 2TR-FE

WIRING DIAGRAM

E290486E02

INSPECTION PROCEDURE


1. READ VALUE USING GTS (CRUISE CONTROL MAIN SWITCH)
  1. Using the GTS, read the Data List (Click here).

    Cruise Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Main SW M-CPU
    Cruise control main switch (Main CPU) / ON or OFF
    ON: Cruise control main switch (ON-OFF) on
    OFF: Cruise control main switch (ON-OFF) off
    -
    Cancel Switch
    CANCEL switch signal / ON or OFF
    ON: CANCEL switch on
    OFF: CANCEL switch off
    -
    SET/COAST Switch
    -SET switch signal / ON or OFF
    ON: -SET switch on
    OFF: -SET switch off
    -
    RES/ACC Switch
    +RES switch signal / ON or OFF
    ON: +RES switch on
    OFF: +RES switch off
    -

    OK:
    The display is as specified in the normal condition column.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT CRUISE CONTROL MAIN SWITCH
  1. Remove the cruise control main switch (Click here).

  1. Inspect the cruise control main switch (Click here).



NG
REPLACE CRUISE CONTROL MAIN SWITCH (Click here)
OK


3. CHECK CRUISE CONTROL SWITCH WIRE
  1. Disconnect the A spiral cable sub-assembly connector.

  1. E178683E32
    Disconnect the B cruise control main switch wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-3 (CCS) - B-3 (CCS)
    Always
    Below 1 Ω
    A-4 (ECC) - B-1 (ECC)
    Always
    Below 1 Ω
    A-3 (CCS) or B-3 (CCS) - Body ground
    Always
    10 kΩ or higher
    A-4 (ECC) or B-1 (ECC) - Body ground
    Always
    10 kΩ or higher

Text in Illustration 
*a
Front view of wire harness connector
(to Spiral Cable Sub-assembly)
*b
Front view of wire harness connector
(to Cruise Control Main Switch)


NG
REPLACE CRUISE CONTROL SWITCH WIRE
OK


4. INSPECT SPIRAL CABLE SUB-ASSEMBLY
  1. Remove the spiral cable sub-assembly (Click here).

  1. Inspect the spiral cable sub-assembly (Click here).



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)
  1. Disconnect the H77 spiral cable sub-assembly connector.

  1. Disconnect the B72*1 or B71*2 ECM connector.

    1. *1: for 1KD-FTV
    2. *2: for 2TR-FE

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1KD-FTV 
    Tester Connection
    Condition
    Specified Condition
    H77-1 (CCS) - B72-23 (CCS)
    Always
    Below 1 Ω
    H77-2 (ECC) - Body ground
    H77-1 (CCS) or B72-23 (CCS) - Body ground
    Always
    10 kΩ or higher
    for 2TR-FE 
    Tester Connection
    Condition
    Specified Condition
    H77-1 (CCS) - B71-40 (CCS)
    Always
    Below 1 Ω
    H77-2 (ECC) - Body ground
    H77-1 (CCS) or B71-40 (CCS) - Body ground
    Always
    10 kΩ or higher

Result 
Result
Proceed to
OK (for 1KD-FTV)
A
OK (for 2TR-FE)
B
NG
C


B
REPLACE ECM (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE ECM (Click here)


← Cruise Control Switch Circuit (Dec 2015 – Mar 2016)Cruise Control Switch Circuit (Jan 2017 – Nov 2017) →