P0522 Engine Oil Pressure Sensor / Switch Low
Diagnostic trouble codes · Vehicles built Apr 2016 – Dec 2016
Also covers:
- P0523 Engine Oil Pressure Sensor / Switch High
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
DESCRIPTION
Refer to DTC P0524 (Click here)| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Idling for 5 second |
Conditions (a) and (b) continue for 5 seconds or more (1 trip detection logic): (a) Ignition switch is ON. (b) Oil pressure sender gauge assembly voltage is 0.05 V or less. |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Idling for 5 second |
Conditions (a) and (b) continue for 5 seconds or more (1 trip detection logic): (a) Ignition switch is ON. (b) Oil pressure sender gauge assembly voltage is 4.6 V or higher. |
|
| DTC No. |
Data List |
| P0522 P0523 |
Engine Oil Pressure |
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
- After replacing an injector assembly, the ECM needs registration (Click here).
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. CHECK HARNESS AND CONNECTOR |
Disconnect the oil pressure sender gauge assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D93-3 (VC) - D99-75 (VCPX)
Always
Below 1 Ω
D93-2 (POP) - D99-118 (POP)
Always
Below 1 Ω
D93-1 (E2) - D99-74 (EPEX)
Always
Below 1 Ω
D93-3 (VC) or D99-75 (VCPX) - Body ground
Always
10 kΩ or higher
D93-2 (POP) or D99-118 (POP) - Body ground
Always
10 kΩ or higher
Reconnect the ECM connector.
|
|
||||
| OK | |
| 2. CHECK ECM TERMINAL VOLTAGE (VC TERMINAL) |
Disconnect the oil pressure sender gauge assembly connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D93-3 (VC) - Body ground
Ignition switch ON
4.5 to 5.5 V
Text in Illustration *a
Front view of wire harness connector
(to Oil Pressure Sender Gauge Assembly)
Reconnect the oil pressure sender gauge assembly connector.
|
|
||||
| OK | |
| 3. REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY |
Replace the oil pressure sender gauge assembly (Click here).
| NEXT | |
| 4. CHECK WHETHER DTC OUTPUT RECURS (P0522 AND/OR P0523) |
Connect the GTS to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON and start the engine.
Start the engine and idle it for 5 second or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
Result Result
Proceed to
P0522 or P0523 is output
A
No DTC is output
B
|
|
||||
| A | |
| 5. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 6. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the GTS to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON and start the engine.
Start the engine and idle it for 5 second or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| NEXT | ||
| ||
