2014-2019 Hiace · Service Manual ENGINE

P0524 Engine Oil Pressure Too Low

Diagnostic trouble codes · Vehicles built Apr 2016 – Dec 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The oil pressure control system reduces and increases engine oil pressure using the oil pressure switching valve in the timing gear case assembly. When the engine speed reaches 3000 rpm while racing the engine after warming it up, the oil pressure switching valve operates and the engine oil pressure system changes from low pressure control mode to high pressure control mode. When the engine speed drops to 2800 rpm, the engine oil pressure system changes from high pressure control mode to low pressure control mode. The oil pressure sender gauge assembly detects the engine oil pressure.
A246647E01
P0524 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
After warming up the engine, race the engine at 3000 rpm or higher.*
Conditions (a) and (b) continue for 5 seconds or more (1 trip detection logic):
(a) 0.3 seconds have elapsed after sending a command to change from low oil pressure control mode to high oil pressure control mode.
(b) The oil pressure control system does not change to high oil pressure control mode.
  1. Short in oil pressure sender gauge assembly circuit
  2. Oil pressure switching valve relay
  3. Oil pressure sender gauge assembly
  4. Oil pressure switching valve assembly
  5. ECM
  6. Oil pump assembly
  7. Engine oil amount insufficient
*: Using the GTS, the oil pressure control system can be inspected by performing Engine Oil Pressure Control Check. Enter the following menus: Powertrain / Engine and ECT/ Utility / Engine Oil Pressure Control Check.

HINT:
Checking the state of the oil level warning light and oil pressure warning light will help in understanding why this DTC was stored (Click here).

Related Data List 
DTC No.
Data List
P0524
Engine Oil Pressure
Eng Oil Press Switch Valve

WIRING DIAGRAM

Refer to DTC P0522 (Click here)

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  3. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  4. After replacing an injector assembly, the ECM needs registration (Click here).

HINT:
  1. Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
  2. An output DTC does not necessarily indicate that there is a malfunction. DTCs may have been stored due to an insufficient engine oil amount even though the oil level warning light is currently not illuminated, such as when engine oil is added by the customer.


1. CHECK ENGINE OIL LEVEL
  1. Check the engine oil level (Click here).

  1. Check the state of the oil level warning light.

    Result 
    Result
    Proceed to
    Engine oil level is low and oil level warning light is illuminated
    A
    Engine oil level is within the specified range and oil level warning light is not illuminated
    B

    HINT:
    If the oil level warning light is not illuminated even though the engine oil level is lower than the Low mark, or the oil level warning light is illuminated even though the engine oil level is within the specified range, inspect the oil level sensor and related parts for malfunctions.



B
Go to step 4
A


2. CHECK ENGINE OIL LEAKS
  1. Check for engine oil leaks.

    Result:
    If there are engine oil leaks, perform repairs.


NEXT


3. ADD ENGINE OIL
  1. Add engine oil.


NEXT


4. INSPECT OIL PUMP ASSEMBLY (OIL PRESSURE SWITCHING VALVE OPERATION)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Start the engine and warm it up.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Engine Oil Pressure Control Check (Click here).

  1. Compare the "valve off" (high pressure control mode) and "valve on" (low pressure control mode) oil pressure values and check the difference.

    Standard:
    50 kPa or higher.



NG
Go to step 5
OK

END

5. CHECK OIL PUMP ASSEMBLY (OIL PRESSURE SWITCHING VALVE OPERATION)
  1. Disconnect the connector of the oil pressure switching valve assembly.

    NOTICE:
    1. Make sure that the engine is stopped before disconnecting the connector of the oil pressure switching valve assembly.
    2. Make sure that the disconnected connector does not get caught in moving engine parts.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Start the engine and warm it up.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Engine Oil Pressure Control Check (Click here).

  1. Check the engine oil pressure value.

    Result 
    Result
    Proceed to
    Engine oil pressure rises to between 170 and 450 kPa
    A
    Except above
    B

    HINT:
    Low oil pressure control mode is not performed when the connector of the oil pressure switching valve assembly is disconnected. Therefore, if the measurement results from Engine Oil Pressure Control Check all indicate oil pressure values which are high, it can be determined that there is an electrical malfunction.



B
Go to step 11
A


6. INSPECT OIL PRESSURE SWITCHING VALVE RELAY (OSV)
  1. Inspect the oil pressure switching valve relay (OSV) (Click here).



NG
Go to step 9
OK


7. CHECK HARNESS AND CONNECTOR
  1. Remove the oil pressure switching valve relay (OSV) from the No. 1 engine room relay block and junction block assembly.

  1. Disconnect the oil pressure switching valve assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    D89-2 (OSV+) - Body ground*
    Always
    10 kΩ or higher
    10A-1 - 10A-2
    Always
    10 kΩ or higher
    10A-1 - Body ground*
    Always
    10 kΩ or higher
    10A-4 - Body ground*
    Always
    10 kΩ or higher
    D99-39 (EOPV) - Body ground*
    Always
    10 kΩ or higher

    HINT:
    *: Make sure that there are no short circuits to the battery

  1. Reinstall the oil pressure switching valve relay (OSV).

  1. Reconnect the oil pressure switching valve assembly connector.

  1. Reconnect the ECM connector.



NG
Go to step 10
OK


8. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 16
9. REPLACE OIL PRESSURE SWITCHING VALVE RELAY (OSV)
  1. Replace the oil pressure switching valve relay (OSV).



NEXT
Go to step 16
10. REPAIR OR REPLACE HARNESS AND CONNECTOR
  1. Repair or replace the harness or connector.



NEXT
Go to step 16
11. INSPECT ENGINE OIL PRESSURE
  1. Inspect the engine oil pressure (Click here).



NG
Go to step 13
OK


12. REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY
  1. Replace the oil pressure sender gauge assembly (Click here).



NEXT
Go to step 16
13. REPLACE OIL PRESSURE SWITCHING VALVE ASSEMBLY
  1. Replace the oil pressure switching valve assembly (Click here).


NEXT


14. INSPECT OIL PUMP ASSEMBLY (OIL PRESSURE SWITCHING VALVE OPERATION)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Start the engine and warm it up.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Engine Oil Pressure Control Check (Click here).

  1. Compare the "valve off" (high pressure control mode) and "valve on" (low pressure control mode) oil pressure values and check that the oil pressure has risen.

    Standard:
    50 kPa or higher.



NG
Go to step 15
OK

END

15. REPAIR OR REPLACE OIL PUMP ASSEMBLY
  1. Repair or replace the oil pump assembly.

    HINT:
    If the oil pressure does not rise after disconnecting the connector of the oil pressure switching valve assembly, or if the oil pressure changes, but the difference between the low oil pressure and high oil pressure is small, a mechanical malfunction is probably the cause.
    1. The sleeve is locked due to foreign matter.
    2. The oil pressure relief valve is locked due to foreign matter.
    3. The check valve is stuck.


NEXT


16. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Start the engine and warm it up.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Engine Oil Pressure Control Check (Click here).

  1. Compare the "valve off" (high pressure control mode) and "valve on" (low pressure control mode) oil pressure values and check that the oil pressure has risen.


NEXT

END


← P0524 Engine Oil Pressure Too Low (Dec 2015 – Mar 2016)P0524 Engine Oil Pressure Too Low (from Jan 2017) →