2014-2019 Hiace · Service Manual BRAKE

VSC OFF Switch Circuit

Circuit diagnosis · Vehicles built Jan 2017 – Nov 2017

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.
Pressing the VSC OFF switch turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation. If TRC and VSC operations are turned off, the TRC OFF indicator light and the VSC OFF indicator light will come on.

WIRING DIAGRAM

C309455E04

INSPECTION PROCEDURE

NOTICE:
When replacing the skid ECU (brake actuator assembly), perform zero point calibration and store system information (Click here).


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check if CAN communication system DTCs are output (Click here).

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
CHECK CAN COMMUNICATION SYSTEM (Click here)
A


2. CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU (brake actuator assembly) connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY
OK


3. READ VALUE USING GTS (TRC/VSC OFF MODE)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. According to the display on the GTS, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    TRC/VSC Off Mode
    TRC/VSC off mode /
    Normal, TRC OFF, Unknown or VSC OFF
    NORMAL: Normal mode
    TRC OFF: TRC off mode
    VSC OFF: VSC off mode
    Unknown: Unspecified

  1. Check the indicator light and mode condition on the GTS changes according to VSC OFF switch operation.

    Standard::
    Switch Operation
    Mode Condition Display
    TRC OFF Indicator Light
    VSC OFF Indicator Light
    Not pressed
    Normal
    Does not come on
    Does not come on
    Pressing the VSC OFF switch
    TRC OFF
    Comes on
    Does not come on
    Pressing and holding the VSC OFF switch
    VSC OFF
    Comes on
    Comes on


    Result:
    Result
    Proceed to
    Indicator light and mode condition display do not change
    A
    Mode condition display is normal, but indicator light does not change
    B
    Indicator light and mode condition display is normal
    C



B
INSPECT METER / GAUGE SYSTEM (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


4. PERFORM ACTIVE TEST USING GTS (TRC OFF INDICATOR LIGHT AND VSC OFF INDICATOR LIGHT)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

  1. According to the display on the GTS, perform the Active Test.

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    TRC(TRAC) OFF Indicator Light
    TRC OFF indicator light
    Indicator light ON/OFF
    Observe combination meter assembly
    Vehicle condition: Vehicle stopped
    VSC OFF Indicator Light
    VSC OFF indicator light
    Indicator light ON/OFF
    Observe combination meter assembly
    Vehicle condition: Vehicle stopped

  1. Check the TRC OFF indicator light and VSC OFF indicator light in the combination meter assembly turn on or off in accordance with GTS operation.

    OK:
    The TRC OFF indicator light and VSC OFF indicator light turn on or off in accordance with GTS operation.



NG
Go to step 7
OK


5. INSPECT VSC OFF SWITCH
  1. Turn the ignition switch off.

  1. Remove the VSC OFF switch (Click here).

  1. Inspect the VSC OFF switch (Click here).

    OK:
    The VSC OFF switch operates normally.



NG
REPLACE VSC OFF SWITCH (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (VSC OFF SWITCH - BRAKE ACTUATOR ASSEMBLY)
  1. Disconnect the B92 skid control ECU (brake actuator assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B92-33 (CSW) - I34-6
    Always
    Below 1 Ω
    B92-33 (CSW) or I34-6 - Body ground
    Always
    10 kΩ or higher
    I34-3 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

7. INSPECT COMBINATION METER ASSEMBLY
  1. Turn the ignition switch off.

  1. Perform the Active Test of the combination meter assembly using the GTS (Click here).

  1. Check the combination meter assembly.

    OK:
    The TRC OFF indicator light and VSC OFF indicator light turn on or off in accordance with GTS operation.



NG
INSPECT METER / GAUGE SYSTEM (Click here)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)


← VSC OFF Switch Circuit (Apr 2016 – Dec 2016)VSC OFF Switch Circuit (from Dec 2017) →