2014-2019 Hiace · Service Manual ENGINE

P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

DESCRIPTION

Refer to DTC P0016 (Click here).
P0342 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 4 seconds or more
Output voltage of camshaft position sensor is less than 0.3 V for 4 seconds.
(1 trip detection logic)
  1. Open or short in camshaft position sensor circuit
  2. Camshaft position sensor
  3. ECM
P0343 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 4 seconds or more
Output voltage of camshaft position sensor is higher than 4.7 V for 4 seconds.
(1 trip detection logic)
  1. Open or short in camshaft position sensor circuit
  2. Camshaft position sensor
  3. ECM

HINT:
  1. If DTC P0342 or P0343 is stored, the following symptoms may appear:
    1. Difficulty starting
    2. Misfire
    3. Combustion noise
    4. Black smoke
    5. White smoke
    6. Lack of power

  2. A340471E01
    Reference: Inspection using an oscilloscope.
    The correct waveform is as shown.
    ECM Terminal Name
    Between G2+ and G2-
    Between NE+ and NE-
    Tester Range
    2 V/DIV., 20 msec./DIV.
    Condition
    Idling with warm engine


MONITOR DESCRIPTION

When the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V for 4 seconds, the ECM stores a DTC.

WIRING DIAGRAM

Refer to DTC P0016 (Click here).

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK DTC OUTPUT
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Disconnect the camshaft position sensor connector.

  1. Turn the ignition switch to ON for 4 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Check whether the DTC changes when the connector is disconnected and connected.

    Result:
    Result
    Proceed to
    DTC does not change
    A
    DTC changes
    B



B
Go to step 5
A


2. CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
  1. Disconnect the camshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D128-3 (VC) - D134-111 (VCG)
    Always
    Below 1 Ω
    D128-1 (G22+) - D134-78 (G2+)
    Always
    Below 1 Ω
    D128-2 (G22-) - C134-77 (G2-)
    Always
    Below 1 Ω
    D128-3 (VC) - D134-111 (VCG) - Body ground and other terminals
    Always
    10 kΩ or higher
    D128-1 (G22+) or D134-78 (G2+) - Body ground and other terminals
    Always
    10 kΩ or higher
    D128-2 (G22-) or D134-77 (G2-) - Body ground and other terminals
    Always
    10 kΩ or higher

  1. Reconnect the camshaft position sensor connector.



NG
Go to step 6
OK


3. CHECK ECM (CAMSHAFT POSITION SENSOR VOLTAGE)

  1. A376492E04
    Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D128-3 (VC) - D128-2 (G22-)
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Camshaft Position Sensor)



NG
Go to step 7
OK


4. CHECK ECM (CHECK RESISTANCE)

  1. A376492E04
    Disconnect the camshaft position sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D128-3 (VC) - D128-1 (G22+)
    Ignition switch off
    No short or no open circuit
    D128-1 (G22+) - D128-2 (G22-)
    Ignition switch off
    No short or no open circuit

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Camshaft Position Sensor)

  1. Reconnect the camshaft position sensor connector.



NG
Go to step 7
OK


5. REPLACE CAMSHAFT POSITION SENSOR
  1. Replace the camshaft position sensor (Click here).



NEXT
Go to step 8
6. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.



NEXT
Go to step 8
7. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 8
8. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Turn the ignition switch to ON for 4 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output.


NEXT

END


← P0337 Crankshaft Position Sensor "A" Circuit Low Input (+ P0338) (from Jan 2017)P0400 Exhaust Gas Recirculation Flow (from Jan 2017) →