2014-2019 Hiace · Service Manual ENGINE

Lack of Power (Turbocharger System)

Circuit diagnosis · Vehicles built from Jan 2017

INSPECTION PROCEDURE

HINT:
  1. The diagnosis flowchart is for lack of power due to turbocharger factors.
  2. If symptom-specific diagnosis indicates a turbocharger related problem, check using this flowchart.


1. CHECK TURBOCHARGER SUB-ASSEMBLY

  1. Check that no soot or oil adheres to the turbocharger sub-assembly connectors.A402454E01

    HINT:
    If adhering soot or an oil leak exists, air leaking at that position may be the cause of the lack of boost pressure.

Result: 
Result
Proceed to
No adhering soot or an oil
A
Soot adhering around the turbine housing, flange, or V band (A in the illustration)
B
Oil leak from the contact surface between the compressor housing and bearing housing (B in the illustration)
C


B
Go to step 5

C
REPLACE TURBOCHARGER SUB-ASSEMBLY (Click here)
A


2. INSPECT TURBOCHARGER SUB-ASSEMBLY (TURBINE SHAFT)
  1. Remove the turbocharger sub-assembly.

    1. Check that the turbine shaft rotates smoothly, without catching.
    2. Check for loose turbine mounting nuts and for axial play in the turbine shaft.

      HINT:
      If the turbine shaft catches or if there is no play or excessive play, it could indicate improper sealing due to seizing or poor sliding because of a deposit build-up.

      Standard value:
      0.10 mm (0.00394 in.) or less

Result: 
Result
Proceed to
No turbine shaft malfunction
A
Turbine shaft malfunction
B


B
REPLACE TURBOCHARGER SUB-ASSEMBLY (Click here)
A


3. INSPECT TURBOCHARGER SUB-ASSEMBLY
  1. Check for interference between the turbine wheel and the turbine housing.

    HINT:
    When there is interference between the turbine wheel and turbine housing and the turbine wheel is damaged, check for fragments of the turbine wheel in the exhaust manifold converter sub-assembly.

Result: 
Result
Proceed to
No damage or interference
A
Damage or interference exists
B


B
REPLACE TURBOCHARGER SUB-ASSEMBLY (Click here)
A


4. INSPECT TURBOCHARGER NOZZLE VANE PLATE

  1. A348999
    Inspect the turbocharger nozzle vane plate.
    1. Remove the e-washer from the turbocharger nozzle vane control actuator.

  1. Move the turbocharger vane control rod sub-assembly and check that the turbocharger nozzle vane plate moves.

Result: 
Result
Proceed to
Catches, but operates*
A
Gets stuck and does not operate
B

HINT:
*: Check several times.



NG
REPLACE TURBOCHARGER SUB-ASSEMBLY (Click here)
OK

REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR (Click here)

5. CHECK EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
  1. Check for deformation or cracks in the mounting surfaces on the exhaust manifold converter sub-assembly and the turbocharger sub-assembly.

    HINT:
    Deformation or cracks on a mounting surface may allow exhaust gas to leak from the damaged position.

    Standard:
    No deformation or cracks on a mounting surface

Result: 
Result
Proceed to
No problem with the mounting surface
A
Deformation or cracks on the exhaust manifold converter sub-assembly mounting surface
B
Deformation or cracks on the turbocharger sub-assembly mounting surface
C


B
REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (Click here)

C
REPLACE TURBOCHARGER SUB-ASSEMBLY (Click here)
A


6. REPLACE EXHAUST PIPE CLAMP AND GASKET
  1. Replace the exhaust pipe clamp and the gasket.


NEXT


7. PERFORM SIMULATION TEST
  1. Check that the abnormal state has disappeared.


NEXT

END


← MIL Circuit (from Jan 2017)COMPONENTS (from Jan 2017) →