2014-2019 Hiace · Service Manual ENGINE

P203C Reductant Level Sensor Circuit Low

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

DESCRIPTION

The urea pump has a level sensor that detects the position of the surface of the fluid inside the urea tank in order to measure the remaining quantity of urea solution.
When the remaining quantity of urea solution falls below a fixed value, a warning is displayed on the combination meter.
P203C 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 3 seconds or more
An open or short in the level sensor (urea pump) circuit for 3 seconds or more.
(1 trip detection logic).
  1. Open or short in the level sensor circuit
  2. Level sensor (urea pump)
  3. Urea pump control ECU
P203D 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 3 seconds or more
An open or short in the level sensor (urea pump) circuit for 3 seconds or more.
(1 trip detection logic)
  1. Open or short in the level sensor circuit
  2. Level sensor (urea pump)
  3. Urea pump control ECU
Related Data List 
DTC No.
Data List
P203C
P203D
Reductant Level

WIRING DIAGRAM

A357972E05

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. INSPECT LEVEL SENSOR (UREA PUMP)
  1. Inspect the level sensor (urea pump) (Click here).



NG
Go to step 7
OK


2. CHECK HARNESS AND CONNECTOR (LEVEL SENSOR (UREA PUMP) - UREA PUMP CONTROL ECU)
A360342E13
Text in Illustration 
*a
Front view of wire harness connector
(to Level Sensor (Urea Pump))
*b
Front view of wire harness connector
(to Urea Pump Control ECU)
  1. Disconnect the level sensor (urea pump) connector.

  1. Disconnect the urea pump control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A47-12 (VLV1) - A45-60 (VCVL)
    Always
    Below 1 Ω
    A47-11 (LV1) - A45-59 (LVU)
    Always
    Below 1 Ω
    A47-6 (ELV1) - A45-58 (ELU)
    Always
    Below 1 Ω
    A47-12 (VLV1) or A45-60 (VCVL) - Body ground and other terminals
    Always
    10 kΩ or higher
    A47-11 (LV1) or A45-59 (LVU) - Body ground and other terminals
    Always
    10 kΩ or higher
    A47-6 (ELV1) or A45-58 (ELU) - Body ground and other terminals
    Always
    10 kΩ or higher

  1. Reconnect the urea pump control ECU connector.

  1. Reconnect the level sensor (urea pump) connector.



NG
Go to step 6
OK


3. CHECK WHETHER DTC OUTPUT RECURS (DTC P203C OR P203D)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON and wait for 3 seconds or more.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result: 
    Result
    Proceed to
    DTC P203C or P203D is output
    A
    DTC is not output
    B



B
END
A


4. REPLACE UREA PUMP CONTROL ECU
  1. Replace the urea pump control ECU (Click here).


NEXT


5. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON and wait for 3 seconds or more.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END

6. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace harness or connector.



NEXT
Go to step 5
7. REPLACE UREA PUMP
  1. Replace the urea pump (Click here).



NEXT
Go to step 5

← P2032 Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 2) (+ P2033) (from Jan 2017)P203F Reductant Level Too Low (from Jan 2017) →