P2048 Reductant Injector Circuit Low (Bank 1 Unit 1)
Diagnostic trouble codes · Vehicles built from Jan 2017
Also covers:
- P2049 Reductant Injector Circuit High (Bank 1 Unit 1)
DESCRIPTION
The urea injector opens the needle valve and injects urea solution according to operation signals sent by the urea pump control ECU.| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Reductant Injection Valve (Active Test) |
When the urea injector is operating, an open or short circuit occurs in the urea injector circuit for 5 seconds or more. (1 trip detection logic) |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Reductant Injection Valve (Active Test) |
When the urea injector is operating, an open or short circuit occurs in the urea injector circuit for 5 seconds or more. (1 trip detection logic) |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. INSPECT UREA INJECTOR SET |
Inspect the urea injector set (Click here).
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (UREA INJECTOR SET - UREA PUMP CONTROL ECU) |


Disconnect the urea injector set connector.
Disconnect the urea pump control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D132-2 - A45-8 (UIV+)
Always
Below 1 Ω
D132-1 - A45-7 (UIV-)
Always
Below 1 Ω
D132-2 or A45-8 (UIV+) - Body ground and other terminals
Always
10 kΩ or higher
D132-1 or A45-7 (UIV-) - Body ground and other terminals
Always
10 kΩ or higher
| *a |
Front view of wire harness connector (to Urea Injector Set) |
*b |
Front view of wire harness connector (to Urea Pump Control ECU) |
|
|
||||
| OK | |
| 3. CLEAR DTC |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
| NEXT | |
| 4. CHECK DTC OUTPUT |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Reductant Injection Valve.
Perform the Active Test.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
- Result:
Result
Proceed to
DTC P2048 or P2049 is output
A
DTCs is not output
B
|
|
||||
| A | |
| 5. REPLACE UREA PUMP CONTROL ECU |
Replace the urea pump control ECU (Click here).
| NEXT | |
| 6. CLEAR DTC |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
| NEXT | |
| 7. CHECK DTC OUTPUT |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Reductant Injection Valve.
Perform the Active Test.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| NEXT | ||
| ||
| 8. REPAIR OR REPLACE HARNESS AND CONNECTOR |
Repair or replace the harness or connector.
|
|
||||
| 9. REPLACE UREA INJECTOR SET |
Replace the urea injector set (Click here).
|
|
||||
