2014-2019 Hiace · Service Manual ENGINE

U010E Lost Communication with Reductant Control Module

Diagnostic trouble codes · Vehicles built from Jan 2017

DESCRIPTION

The ECM sends and receives data to and from the urea pump control ECU via local CAN communication.
U010E 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
1.6 seconds or more after turning the ignition switch to ON.
Communication stops between the ECM and the urea pump control ECU for 1.6 seconds or more.
  1. Urea pump control ECU
  2. Harness or connector
  3. ECM

MONITOR DESCRIPTION

The ECM stores a DTC when a communication malfunction occurs between the ECM and urea pump control ECU.

WIRING DIAGRAM

A355546E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses of circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK DTC OUTPUT
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. According to the display on the GTS, select "Health Check".

  1. Check for currently output system DTCs.

    Result:
    Result
    Proceed to
    DTC U010E is output
    A
    DTC U010E and other DTCs are output*
    B

    HINT:
    *: If any other DTCs are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. CHECK HARNESS AND CONNECTOR (UREA PUMP CONTROL ECU - ECM)
  1. Disconnect the urea pump control ECU connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A45-27 (CAN+) - B97-41 (CANU)
    Always
    Below 1 Ω
    A45-26 (CAN-) - B97-56 (CAND)
    Always
    Below 1 Ω
    A45-27 (CAN+) or B97-41 (CANU) - Body ground and other terminals
    Always
    10 kΩ or higher
    A45-26 (CAN-) or B97-56 (CAND) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3. CHECK UREA PUMP CONTROL ECU (BATT TERMINAL)

  1. A204368E32
    Disconnect the urea pump control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A45-30 (BATT) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Urea Pump Control ECU)



NG
REPLACE UREA PUMP CONTROL ECU (Click here)
OK


4. CHECK DCU RELAY
  1. Inspect the DCU relay (Click here).



NG
REPLACE DCU MAIN RELAY (DCU)
OK


5. CHECK UREA PUMP CONTROL ECU (UREL TERMINAL)
  1. Remove the DCU relay from the instrument panel relay block.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    DCU relay terminal 1 - Body ground
    Ignition switch ON
    11 to 14 V



NG
Go to step 7
OK


6. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL RELAY BLOCK - UREA PUMP CONTROL ECU)
  1. Remove the DCU relay from the instrument panel relay block.

  1. Disconnect the urea pump control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DCU relay terminal 3 - A45-11 (+BSU1)
    Always
    Below 1 Ω
    DCU relay terminal 3 - A45-10 (+BSU2)
    Always
    Below 1 Ω
    DCU relay terminal 3 - A45-19 (+BSU3)
    Always
    Below 1 Ω
    DCU relay terminal 3 - A45-1 (+BSU4)
    Always
    Below 1 Ω
    DCU relay terminal 3 - A45-2 (+BSU5)
    Always
    Below 1 Ω
    DCU relay terminal 2 - Body ground
    Always
    Below 1 Ω
    DCU relay terminal 3 or A45-11 (+BSU1) - Body ground and other terminals
    Always
    10 kΩ or higher
    DCU relay terminal 3 or A45-10 (+BSU2) - Body ground and other terminals
    Always
    10 kΩ or higher
    DCU relay terminal 3 or A45-19 (+BSU3) - Body ground and other terminals
    Always
    10 kΩ or higher
    DCU relay terminal 3 or A45-1 (+BSU4) - Body ground and other terminals
    Always
    10 kΩ or higher
    DCU relay terminal 3 or A45-2 (+BSU5) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (INSTRUMENT PANEL RELAY BLOCK - BATTERY)

7. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL RELAY BLOCK - UREA PUMP CONTROL ECU)
  1. Remove the DCU relay from the instrument panel relay block.

  1. Disconnect the urea pump control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DCU relay terminal 1- A45-9 (UREL)
    Always
    Below 1 Ω
    DCU relay terminal 1 or A45-9 (UREL) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE UREA PUMP CONTROL ECU (Click here)


← P2610 ECM / PCM Internal Engine Off Timer Performance (from Jan 2017)U029D Lost Communication with NOx Sensor "A" (from Jan 2017) →