2014-2019 Hiace · Service Manual ENGINE

U029D Lost Communication with NOx Sensor "A"

Diagnostic trouble codes · Vehicles built from Jan 2017

DESCRIPTION

The ECM sends and receives data to and from the nitrogen oxides sensor via local CAN communication.
U029D 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Turn the ignition switch to ON and wait for 1.6 seconds or more.
Communication stops between the ECM and the nitrogen oxides sensor for 1.6 seconds or more.
  1. Nitrogen oxides sensor
  2. Harness or connector
  3. ECM

MONITOR DESCRIPTION

The ECM stores a DTC when a communication malfunction occurs between the nitrogen oxides sensor and ECM.

WIRING DIAGRAM

A358344E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses of circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK DTC OUTPUT
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. According to the display on the GTS, select "Health Check".

  1. Check for currently output system DTCs.

    Result:
    Result
    Proceed to
    DTC U029D is output
    A
    DTC U029D and other DTCs are output*
    B

    HINT:
    *If any other DTCs are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. CHECK NITROGEN OXIDES SENSOR
  1. Disconnect the nitrogen oxides sensor connector.

  1. Turn the ignition switch to ON.

  1. A383897E02
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    r7-5 (BATT) - r7-4 (GND)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Nitrogen oxides sensor)



NG
Go to step 6
OK


3. CHECK HARNESS AND CONNECTOR (NITROGEN OXIDES SENSOR - ECM)
  1. Disconnect the nitrogen oxides sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    r7-2 (CAN+) - B97-41 (CANU)
    Always
    Below 1 Ω
    r7-3 (CAN-) - B97-56 (CAND)
    Always
    Below 1 Ω
    r7-2 (CAN+) or B97-41 (CANU) - Body ground and other terminals
    Always
    10 kΩ or higher
    r7-3 (CAN-) or B97-56 (CAND) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. REPAIR NITROGEN OXIDES SENSOR
  1. Replace the nitrogen oxides sensor (Click here).


NEXT


5. CHECK DTC OUTPUT
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs.

  1. Turn the ignition switch off for 30 seconds or more.

  1. Turn the ignition switch to ON wait for 1.6 seconds or more.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    No DTC is output
    A
    DTC U029D is output
    B



B
REPLACE ECM (Click here)
A

END

6. INSPECT NOX RELAY
  1. Inspect NOX relay (Click here).



NG
REPLACE NOX PM RELAY
OK


7. CHECK HARNESS AND CONNECTOR (NITROGEN OXIDES SENSOR - ENGINE ROOM RELAY BLOCK, BATTERY - ENGINE ROOM RELAY BLOCK)
  1. Disconnect the nitrogen oxides sensor connector.

  1. Remove the NOx PM relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    r7-5 (BATT) - NOX relay terminal 3
    Always
    Below 1 Ω
    r7-4 (GND) - Body ground
    Always
    Below 1 Ω
    NOX relay terminal 1 - Body ground
    Always
    Below 1 Ω
    NOX relay terminal 3 or r7-5 (BATT) - Body ground and other terminals
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    NOX relay terminal 5 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO ECM POWER SOURCE CIRCUIT (Click here)


← U010E Lost Communication with Reductant Control Module (from Jan 2017)Engine Difficult to Start or Stalling (from Jan 2017) →