The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine unit removal/installation are shown below.
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is operated normally
| *a | An Object Exceeding Weight Limit of Engine Lifter |
The engine assembly with transmission is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly may fall off the engine lifter.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
1.REMOVE AIR SWITCHING VALVE ASSEMBLY (w/ Secondary Air Injection System)
17360G
2.REMOVE AIR TUBE ASSEMBLY (w/ Secondary Air Injection System)
Remove the bolt and air tube assembly.
12261
3.REMOVE PCV HOSE
Slide the clip and remove the PCV hose from the PCV valve.
12262
4.REMOVE NO. 2 PCV HOSE
Slide the clip and remove the No. 2 PCV hose from the cylinder head cover sub-assembly.
23901
5.REMOVE FUEL TUBE SUB-ASSEMBLY AND NO. 2 FUEL TUBE SUB-ASSEMBLY
Detach the 2 clamps and remove the fuel tube clamp.
| *1 | Fuel Tube Sub-assembly |
| *2 | No. 2 Fuel Tube Sub-assembly |
Disconnect the fuel tube sub-assembly.
Click hereEngine / Hybrid System>7GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
Detach the 2 clamps and disconnect the No. 2 fuel tube sub-assembly.
Disconnect the No. 2 fuel tube sub-assembly.
Click hereEngine / Hybrid System>7GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
6.REMOVE HEATER WATER HOSE ASSEMBLY
| *A | w/o ATF Warmer |
| *B | w/ ATF Warmer |
w/o ATF Warmer:
Slide the hose clamp and disconnect the heater water hose assembly from the rear water by-pass joint.
Slide the hose clamp and disconnect the heater water hose assembly from the No. 1 water outlet pipe.
Remove the bolt and remove the heater water hose assembly.
w/ ATF Warmer:
Slide the hose clamp and disconnect the heater water hose assembly from the rear water by-pass joint.
Remove the bolt and remove the heater water hose assembly.
29300
7.REMOVE VACUUM PUMP ASSEMBLY
88431
8.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
Remove the 2 bolts and No. 1 compressor mounting bracket.
12315
9.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH
Remove the 3 bolts and front No. 1 engine mounting bracket LH.
12311
10.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH
Remove the 4 bolts and front No. 1 engine mounting bracket RH.
16603
11.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY
Remove the bolt and No. 1 idler pulley sub-assembly.
16604
12.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY
| *A | LH Side |
| *B | RH Side |
Remove the 2 bolts and 2 No. 2 idler pulley sub-assemblies.
16620
13.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
While turning the V-ribbed belt tensioner counterclockwise, align the service hole for the V-ribbed belt tensioner and the V-ribbed belt tensioner fixing position, and then insert a bar of 6 mm (0.236 in.) into the service hole to fix the V-ribbed belt tensioner in place.
The pulley bolt for the V-ribbed belt tensioner has a left-hand thread.
Remove the 2 bolts and V-ribbed belt tensioner assembly.
16281
14.REMOVE NO. 4 WATER BY-PASS HOSE
Slide the hose clamp and remove the No. 4 water by-pass hose.
16282
15.REMOVE NO. 5 WATER BY-PASS HOSE
Slide the hose clamp and remove the No. 5 water by-pass hose.
16261
16.REMOVE NO. 1 WATER BY-PASS HOSE
Slide the 2 hose clamps and remove the No. 1 water by-pass hose.
16264
17.REMOVE NO. 2 WATER BY-PASS HOSE
Slide the 2 hose clamps and remove the No. 2 water by-pass hose.
16267
18.REMOVE NO. 3 WATER BY-PASS HOSE
Slide the 2 hose clamps and remove the No. 3 water by-pass hose.
16268
19.REMOVE NO. 1 WATER BY-PASS PIPE
Slide the 4 hose clamps and disconnect the 4 water by-pass hoses.
Remove the 3 bolts, nut and No. 1 water by-pass pipe.
82121
20.REMOVE ENGINE WIRE
17111
21.REMOVE INTAKE MANIFOLD
23801P
22.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY
23100X
23.REMOVE FUEL PUMP ASSEMBLY
23802B
24.REMOVE NO. 2 FUEL PIPE SUB-ASSEMBLY
23860
25.REMOVE FUEL DELIVERY WITH SENSOR PIPE ASSEMBLY LH
23814E
26.REMOVE FUEL DELIVERY PIPE RH
23250E
27.REMOVE DIRECT FUEL INJECTOR ASSEMBLY
23255A
28.REMOVE FUEL INJECTOR SEAL
19500
29.REMOVE IGNITION COIL ASSEMBLY
83530
30.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY
89422P
31.REMOVE ENGINE COOLANT TEMPERATURE SENSOR