Home › Brake › BRAKE SYSTEM (OTHER) › VACUUM PUMP (for 1GD-FTV)
RM35X0E _54 Brake _078668 BRAKE SYSTEM (OTHER) _0381545 VACUUM PUMP(for 1GD-FTV) A

BRAKE SYSTEM (OTHER)  VACUUM PUMP(for 1GD-FTV)  INSTALLATION  


PROCEDURE

Hide 29300F 1.INSTALL VACUUM PUMP UNION

a.
C323737

Install the 2 new gaskets and the vacuum pump union with the union bolt.

Torque:
13.7 N*m (140 kgf*cm, 10 ft.*lbf)

HINT:

Check that the stopper of the vacuum pump union with union bolt is securely held on the vacuum pump assembly.



Hide 11382C 2.INSTALL CAMSHAFT OIL SEAL RETAINER

a.

Install a new camshaft oil seal retainer to the vacuum pump assembly.


Hide 29300 3.TEMPORARILY INSTALL VACUUM PUMP ASSEMBLY

a.

When using new vacuum pump assembly:

i.
A343513C01
1.427,1.656 0.854,1.854 0.854,1.854 0.698,1.854 false 1.229,0.458 1.063,0.302 1.063,0.302 0.865,0.302 true 0.646,0.229 0.844,0.438 0.198,0.208 10 true *1 0.479,1.771 0.667,1.948 0.188,0.177 10 false *2
*1 No. 2 O-ring
*2 No. 3 O-ring
V100135

Engine Oil


Apply engine oil to the No. 2 O-ring and No. 3 O-ring installed in a new vacuum pump assembly.



b.

When reusing vacuum pump assembly:

i.

Install a new No. 2 O-ring and No. 3 O-ring to the vacuum pump assembly.


ii.
A343513C01
1.427,1.656 0.854,1.854 0.854,1.854 0.698,1.854 false 1.229,0.458 1.063,0.302 1.063,0.302 0.865,0.302 true 0.646,0.229 0.844,0.438 0.198,0.208 10 true *1 0.479,1.771 0.667,1.948 0.188,0.177 10 false *2
*1 No. 2 O-ring
*2 No. 3 O-ring
V100135

Engine Oil


Apply engine oil to the No. 2 O-ring and No. 3 O-ring installed in a vacuum pump assembly.



c.
C412544C02
0,0 0,0 false
V113147

Install in this Direction


Temporarily install the vacuum pump assembly.

NOTICE:

Do not insert the vacuum pump assembly into the camshaft until the No. 3 camshaft bearing cap is installed.



Hide 29300 5.INSTALL VACUUM PUMP ASSEMBLY

a.

Install the vacuum pump assembly so that the oil pipe engages with the hole of the camshaft and the coupling teeth with the grooves on the camshaft tip.

NOTICE:
·

Ensure that the vacuum pump assembly is installed securely.

·

Be careful not to pinch the O-ring.




b.
C412542

Install the vacuum pump assembly with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:

After installation, check that there are no gaps between the matching surfaces and that the vacuum pump assembly is not installed at an angle.



Hide 44773F 6.CONNECT UNION TO CONNECTOR TUBE HOSE

a.
C412541

Connect the union to connector tube hose, and slide the clamp to secure it.


b.

Connect the No. 1 vacuum transmitting hose to the vacuum pump assembly.


Hide 29300 8.INSPECT VACUUM PUMP OPERATION