When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
| Injector assembly (including shuffling the injector assemblies between the cylinders) | ·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly |
| Supply pump assembly | Fuel inlet pipe sub-assembly |
·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Cylinder head gasket ·
Timing chain case assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly ·
Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.
The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.
The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.
Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.
Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.
Make sure foreign matter does not enter the fuel path.
1.INSTALL CAMSHAFT
| *1 | Valve Rocker Arm Sub-assembly |
| *2 | Valve Stem Cap |
| *3 | Valve Lash Adjuster Assembly |
Check that the valve rocker arm sub-assembly is firmly set to the valve lash adjuster assembly.
Apply a light coat of engine oil to the camshaft journals of the cylinder head sub-assembly and the thrust portion of the camshaft.
| *a | Paint Mark |
| *b | Timing Mark |
Align the paint mark of the No. 2 chain sub-assembly and timing mark of the camshaft timing sprocket, and install the camshaft timing sprocket to the No. 2 chain sub-assembly.
Make sure the timing mark of the camshaft timing sprocket faces the front side.
Align the knock pin of the No. 1 camshaft to the groove of the sprocket, install the No. 1 camshaft to the camshaft timing sprocket, and set the bolt.
| *a | Paint Mark |
| *b | Timing Mark |
Align the paint mark of the No. 2 chain sub-assembly and timing mark of the camshaft timing sprocket, and install the camshaft timing sprocket to the No. 2 chain sub-assembly.
Make sure the timing mark of the camshaft timing sprocket faces the front side.
Align the knock pin of the No. 2 camshaft to the groove of the sprocket, install the No. 2 camshaft to the camshaft timing sprocket, and set the bolt.
| *a | Groove |
The groove is at the rear end of the No. 2 camshaft.
| *a | Paint Mark |
| *b | Timing Mark |
Check the timing mark of the camshaft timing sprocket and paint mark of the No. 2 chain sub-assembly.
Set the No. 1 camshaft bearing cap and 8 No. 2 camshaft bearing caps to the cylinder head sub-assembly as shown in the illustration.
Temporarily install the 20 bolts.
|
Bolt A |
|
Bolt B |
Uniformly tighten the 20 bolts in several steps in the order shown in the illustration.
| *1 | No. 1 Camshaft |
| *2 | No. 2 Camshaft |
Hold the hexagonal portion of the No. 1 camshaft and No. 2 camshaft with a wrench, and tighten the 2 bolts.
Be careful not to damage the cylinder head sub-assembly with the wrench.
Remove the pin from the No. 2 chain tensioner assembly.
Install a new gasket and the oil pump relief valve plug to the timing chain cover.
13566B
2.INSTALL TIMING CHAIN GUIDE
Install the timing chain guide to the cylinder head sub-assembly with the bolt.
11382C
3.INSTALL CAMSHAFT OIL SEAL RETAINER
29300
4.TEMPORARILY INSTALL VACUUM PUMP ASSEMBLY
5.INSTALL NO. 3 CAMSHAFT BEARING CAP
Clean and degrease the contact surfaces of the cylinder head sub-assembly and No. 3 camshaft bearing cap.
| *a | Seal Packing |
Apply seal packing to the specified areas as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
3.0 mm (0.118 in.)
Do not allow seal packing to contact the oil passage of the No. 3 camshaft bearing cap.
After applying seal packing, install the No. 3 camshaft bearing cap within 3 minutes and tighten the bolts within 10 minutes.
Do not start the engine for at least 2 hours after installation.
Install the No. 3 camshaft bearing cap with the 2 bolts.
Wipe off excess seal packing from between the No. 3 camshaft bearing cap and cylinder head sub-assembly.
29300
6.INSTALL VACUUM PUMP ASSEMBLY
11201
7.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
23682
8.INSTALL NOZZLE HOLDER GASKET
23670
9.TEMPORARILY INSTALL INJECTOR ASSEMBLY
10.TEMPORARILY INSTALL NO. 1 INJECTION PIPE SUB-ASSEMBLY AND NO. 2 INJECTION PIPE SUB-ASSEMBLY
23670
11.TIGHTEN INJECTOR ASSEMBLY
12.TIGHTEN NO. 1 INJECTION PIPE SUB-ASSEMBLY AND NO. 2 INJECTION PIPE SUB-ASSEMBLY
23760
13.INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY
14.INSTALL HARNESS BRACKET
15.INSTALL WIRING HARNESS CLAMP BRACKET
23811H
16.INSTALL NO. 1 FUEL PIPE (w/ DPF)
17.INSTALL NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY
25601
18.CONNECT EGR PIPE WITH COOLER SUB-ASSEMBLY (for Double Actuator EGR Bypass Valve)
25601
19.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY (for Single Actuator EGR Bypass Valve)
16209
20.CONNECT NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY
16206B
21.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY
25612
22.INSTALL NO. 2 EGR PIPE
25625
23.INSTALL EGR VALVE BRACKET
25804
24.INSTALL VACUUM CONTROL VALVE SET
82121
25.CONNECT ENGINE WIRE
23941
26.CONNECT NO. 1 FUEL FILTER PROTECTOR
12632
27.INSTALL NO. 2 ENGINE COVER BRACKET
23265C
28.INSTALL GAS FILTER
89421C
29.INSTALL DIESEL TURBO PRESSURE SENSOR
16278
30.INSTALL NO. 2 WATER BY-PASS PIPE
87209
31.INSTALL WATER HOSE SUB-ASSEMBLY (w/ Heater)
26100G
32.INSTALL DIESEL THROTTLE BODY ASSEMBLY
17303T
33.INSTALL AIR PIPE SUB-ASSEMBLY
25760F
34.INSTALL VACUUM TRANSMITTING HOSE ASSEMBLY
12601B
35.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Cover)
16400
36.INSTALL RADIATOR ASSEMBLY
32922A
37.CONNECT OIL COOLER OUTLET HOSE (for Automatic Transmission)
32921D
38.CONNECT OIL COOLER INLET HOSE (for Automatic Transmission)
53205
39.INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY
86510
40.INSTALL HIGH PITCHED HORN ASSEMBLY (for 2-piece Type)
Click hereVehicle Exterior>HORN>HORN>INSTALLATION
86520
41.INSTALL LOW PITCHED HORN ASSEMBLY
Click hereVehicle Exterior>HORN>HORN>INSTALLATION
16546
42.INSTALL RADIATOR PROTECTOR (w/o Air Conditioning System)
53209B
43.INSTALL HOOD LOCK SUPPORT BRACE SUB-ASSEMBLY
88590
44.INSTALL BLOWER ASSEMBLY WITH SHROUD (w/ Condenser Fan)
for LH Side:
Click hereVehicle Interior>HEATING / AIR CONDITIONING>CONDENSER FAN>INSTALLATION
for RH Side:
Click hereVehicle Interior>HEATING / AIR CONDITIONING>CONDENSER FAN>INSTALLATION
17311B
45.INSTALL NO. 1 AIR INLET DUCT
53510
46.INSTALL HOOD LOCK ASSEMBLY
47.INSTALL FRONT BUMPER
16572D
48.INSTALL NO. 2 RADIATOR HOSE
16711
49.INSTALL FAN SHROUD
88359
50.INSTALL VISCOUS HEATER V BELT (w/ Viscous Heater)
16571C
51.INSTALL NO. 1 RADIATOR HOSE
16470
52.INSTALL RADIATOR RESERVE TANK ASSEMBLY
17030
53.INSTALL AIR HOSE ASSEMBLY
44360
54.CONNECT VANE PUMP OIL RESERVOIR ASSEMBLY
17751
55.INSTALL NO. 1 AIR CLEANER INLET
53106B
56.INSTALL RADIATOR COVER SUB-ASSEMBLY
55701J
57.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY
85110
58.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY
59.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
60. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
61.ADD ENGINE COOLANT
62.INSPECT FOR COOLANT LEAK
63.BLEED AIR FROM FUEL SYSTEM
64.INSPECT FOR FUEL LEAK
51405A
65.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
52618
66.INSTALL LOWER FRONT BUMPER ABSORBER
51406A
67.INSTALL NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 2 Engine Under Cover Sub-assembly)