Home › Audio / Visual / Telematics › AUDIO / VIDEO › STEREO JACK ADAPTER ASSEMBLY (for RHD) › 2019.02–2019.06
RM35X0E _56 Audio / Visual / Telematics _078377 AUDIO / VIDEO _0381942 STEREO JACK ADAPTER ASSEMBLY(for RHD) A

AUDIO / VIDEO  STEREO JACK ADAPTER ASSEMBLY(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during No. 1 stereo jack adapter assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative(-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the systems is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*: w/ Stop and start system

Stop and start system* Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION (w/o Console Tray)

CAUTION:
B407254

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type B)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/o Console Tray)


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative(-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 67911B 3.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE RH (w/o Console Tray)

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL


Hide 67913B 4.REMOVE FRONT DOOR SCUFF PLATE RH (w/o Console Tray)

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL


Hide 62111C 5.REMOVE COWL SIDE TRIM BOARD RH (w/o Console Tray)

Hide 55631A 6.REMOVE NO. 1 INSTRUMENT PANEL UNDER TRAY STOPPER

Hide 55011A 7.REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY (w/o Console Tray)

Hide 55317A 8.REMOVE INSTRUMENT SIDE PANEL RH (w/o Console Tray)

Hide 55641 9.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER (w/o Console Tray)

Hide 53601 10.REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (w/o Console Tray)

Hide 77306 11.REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (w/o Console Tray)

Hide 55432D 12.REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL (w/o Console Tray)

Hide 55044C 13.REMOVE INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (w/o Console Tray)

Hide 55433B 14.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL (w/o Console Tray)

Hide 73900 15.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/o Console Tray)

Hide 67912A 16.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE LH (w/o Console Tray)

Hide 67914B 17.REMOVE FRONT DOOR SCUFF PLATE LH (w/o Console Tray)

Hide 62112 18.REMOVE COWL SIDE TRIM BOARD LH (w/o Console Tray)

Hide 55632B 19.REMOVE NO. 2 INSTRUMENT PANEL UNDER TRAY SUPPORT

Hide 55012A 20.REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY (w/o Console Tray)

Hide 55318C 21.REMOVE INSTRUMENT SIDE PANEL LH (w/o Console Tray)

Hide 55642 22.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER (w/o Console Tray)

Hide 55438A 23.REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL RETAINER (w/o Console Tray)

Hide 58533C 24.REMOVE CENTER FLOOR CARPET COVER RH (w/o Console Tray)

Hide 58534E 25.REMOVE CENTER FLOOR CARPET COVER LH (w/o Console Tray)

Hide 55646 26.REMOVE NO. 3 INSTRUMENT PANEL UNDER COVER (w/o Console Tray)

Hide 55524 27.REMOVE SWITCH BASE HOLE COVER (w/ Console Tray)

Hide 86190C 28.REMOVE NO. 1 STEREO JACK ADAPTER ASSEMBLY

a.

w/o Console Tray:

i.
E416311C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and remove the No. 1 stereo jack adapter assembly as shown in the illustration.



b.

w/ Console Tray:

i.
E416313C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and remove the No. 1 stereo jack adapter assembly as shown in the illustration.