Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING (for Full-trim) › 2019.02–2019.06
RM35X0E _58 Vehicle Interior _078375 INTERIOR PANELS / TRIM _0381233 ROOF HEADLINING(for Full-trim) A

INTERIOR PANELS / TRIM  ROOF HEADLINING(for Full-trim)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the roof headlining assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the systems is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures not Performed Necessary Procedures Link

*: w/ Stop and start system

Stop and start system* Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION (w/ Airbag System)

CAUTION:
B407254

Be sure to read Precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Airbag System)


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 61890A 3.REMOVE BACK WINDOW GLASS HAMMER ASSEMBLY (w/ Hammer)

Hide 67912A 4.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE LH

a.

for Upper Side:

i.
B519196C01
0,0 0,0 false
V113147

Remove in this Direction
V100155

Protective Tape


Insert a thin-bladed screwdriver at the position shown in the illustration, detach the claw.

HINT:

Tape the thin-bladed screwdriver tip before use.



ii.
B519197C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place both hands at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw and guide and remove the front door outside scuff plate LH.



b.

for Lower Side:

i.
B519198C01
0,0 0,0 false
V113147

Remove in this Direction
V100155

Protective Tape


Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and guide and remove the front door outside scuff plate LH.

HINT:

Tape the thin-bladed screwdriver tip before use.




Hide 67914B 5.REMOVE FRONT DOOR SCUFF PLATE LH

a.
B565449

Remove the 6 bolts.


b.

Detach the claw and remove the front door scuff plate LH.


Hide 67911B 6.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 67913B 7.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 62112 8.REMOVE COWL SIDE TRIM BOARD LH

Hide 62111C 9.REMOVE COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure described for the LH side.


Hide 62312B 10.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62311B 11.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 74680 12.REMOVE PILLAR ASSIST GRIP ASSEMBLY LH

a.
B519200C01
0,0 0,0 false
V100155

Protective Tape


Insert a thin-bladed screwdriver at the position shown in the illustration, detach the claw and remove the 2 assist grip covers.

HINT:

Tape the thin-bladed screwdriver tip before use.



b.
B519201

Remove the 2 bolts and pillar assist grip assembly LH.


Hide 74680 13.REMOVE PILLAR ASSIST GRIP ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 62212 14.REMOVE FRONT PILLAR GARNISH LH

a.
B519202C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


b.
B519203C01
0,0 0,0 false
V113147

Remove in this Direction


Pull in the direction of the arrow shown in the illustration to detach the guide and remove the front pillar garnish LH.


c.
B519223C01
1.156,1.531 1.573,1.115 true 1,1.479 1.229,1.677 0.229,0.198 10 true *a
*a Protective Cover
V100155

Adhesive Tape


w/ Curtain Shield Airbag:

Protect the curtain shield airbag assembly LH.

i.

Completely cover the curtain shield airbag assembly LH with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

NOTICE:

Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.




Hide 62211 15.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 17.REMOVE REAR SEAT ASSEMBLY LH

Hide 18.REMOVE REAR SEAT ASSEMBLY RH

a.

for Commuter, Single-Passenger Seat with 2-Point Type Seat Belt:

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Commuter, Single-Passenger Seat with 2-Point Type Seat Belt)>REMOVAL


b.

for Commuter, 2-Passenger Seat with 2-Point Type Seat Belt without Headrest:

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Commuter, 2-Passenger Seat with 2-Point Type Seat Belt without Headrest)>REMOVAL



Hide 73178C 19.REMOVE SEAT BELT ANCHOR COVER CAP

Hide 73233 20.REMOVE OUTER LAP BELT ANCHOR COVER

Hide 73220 21.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH

a.
B541701

Remove the bolt and floor anchor of the front seat outer belt assembly LH.


b.
B541704

Remove the bolt and shoulder anchor of the front seat outer belt assembly LH.


Hide 73210 22.REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 74733 23.REMOVE NO. 1 HAND GRIP COVER (for RHD, w/ Hand Rail)

a.
B539614

Detach the clip and claw and remove the No. 1 hand grip cover.


Hide 74708 24.REMOVE NO. 2 HAND GRIP FRAME SUB-ASSEMBLY (for RHD, w/ Hand Rail)

a.
B539615

Remove the 6 bolts.


b.

Detach the guide and remove the No. 2 hand frame sub-assembly.


Hide 67917C 25.REMOVE REAR DOOR SCUFF PLATE RH

a.

for Standard Roof:

i.
B519239C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place both hands at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


ii.
B519240C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip and guide.


iii.
B519241C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


w/ Power Slide Door:

Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


iv.
B519242C02
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


w/o Power Slide Door:

Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


v.
B519243C01
0,0 0,0 false
V113147

Remove in this Direction


Move the rear door scuff plate RH toward the rear of the vehicle.


vi.
B519244C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door scuff plate RH in the direction indicated by the arrow shown in the illustration.



b.

for High Roof:

i.
B519245C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place both hands at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


ii.
B519246C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip and guide.


iii.
B519247C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


w/ Power Slide Door:

Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


iv.
B519248C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


w/o Power Slide Door:

Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


v.
B519249C01
0,0 0,0 false
V113147

Remove in this Direction


Move the rear door scuff plate RH toward the rear of the vehicle.


vi.
B519250C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door scuff plate RH in the direction indicated by the arrow shown in the illustration.



c.

w/ Interior Illumination:

Disconnect the connector.


d.

w/ Scuff Plate Light:

Disconnect the connector.


Hide 74617A 26.REMOVE ASSIST GRIP PLUG (w/ Assist Grip)

HINT:

Use the same procedure for both assist grip plugs.


a.
B519205

Insert moulding remover A at the position shown in the illustration, detach the claw and guide and remove the assist grip plug.


Hide 74680 27.REMOVE PILLAR ASSIST GRIP ASSEMBLY B (w/ Assist Grip)

a.
B519206

Remove the 2 bolts and pillar assist grip assembly B.


Hide 67871E 28.REMOVE NO. 1 SLIDE DOOR WEATHERSTRIP RH

HINT:

Pull back the No. 1 slide door weatherstrip RH so that the lower center pillar garnish RH and center pillar garnish RH can be removed.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP (except Wagon)>REMOVAL


Hide 62413A 29.REMOVE LOWER CENTER PILLAR GARNISH RH

a.
B519212C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place both hands at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw.


b.
B519213

Using a clip remover, detach the clip.


c.
B519214C01
0,0 0,0 false
V113147

Remove in this Direction


Pull as shown to detach the clip and remove the lower center pillar garnish RH.


Hide 62411 30.REMOVE CENTER PILLAR GARNISH RH

a.
B519204

Remove the clip.


b.
B519215

Using a clip remover, detach the clip.


c.
B519216C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place both hands at the position shown in the illustration, pull in the direction indicated by the arrow to detach the clip and remove the center pillar garnish RH.


Hide 67935 31.REMOVE BACK DOOR SCUFF PLATE

a.
B519224C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and clip and remove the back door scuff plate as shown illustration.


Hide 73370E 32.REMOVE REAR SEAT OUTER BELT ASSEMBLY LH (w/ Seat Belt)

a.
B541717

Remove the bolt and floor anchor of the rear seat outer belt assembly LH.


b.
B541718C01
0,0 0,0 false
V113147

Open in this Direction


Using moulding remover D, detach the claw and open the cover as shown in the illustration.


c.
B541720

Remove the bolt.


Hide 73360D 33.REMOVE REAR SEAT OUTER BELT ASSEMBLY RH (w/ Seat Belt)

HINT:

Use the same procedure described for the LH side.


Hide 58777A 34.REMOVE TOOL BAG HOLDER

a.
B539645

Remove the 3 bolts and tool bag holder.


Hide 62640M 35.REMOVE REAR QUARTER TRIM BOARD ASSEMBLY LH

a.
B519227C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip and claw.


b.
B519228C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip, guide and claw.


c.
B519229C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip and claw.


d.
B519230C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow detach the clip, claw and guide.


e.
B519231C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the clip and remove the rear quarter trim board assembly LH as shown in the illustration.


f.

w/ USB Charger:

Disconnect the connector.


Hide 62620K 36.REMOVE SIDE TRIM BOARD ASSEMBLY LH (for High Roof)

a.
B519255C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw and clip.


b.
B519256C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw and clip.


c.
B519257C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip, claw and guide.


d.
B519258C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place both hands at the position shown in the illustration, pull in the direction indicated by the arrow to detach the clip and remove the side trim board assembly LH.


e.

w/ USB Charger:

Disconnect the connector.


Hide 62520B 37.REMOVE QUARTER TRIM PANEL ASSEMBLY LH

a.
B532736C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow detach the claw and clip.


b.
B532737C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw and clip.


c.
B539563C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


d.
B539564C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


e.
B539565C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the clip and remove the quarter trim panel assembly LH as shown in the illustration.


f.

w/ USB Charger:

Disconnect the connector.


Hide 67871E 38.REMOVE NO. 1 SLIDE DOOR WEATHERSTRIP RH

HINT:

Pull back the No. 1 slide door weatherstrip RH so that the rear quarter trim board assembly RH or side trim board assembly RH can be removed.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP (except Wagon)>REMOVAL


Hide 62630L 39.REMOVE REAR QUARTER TRIM BOARD ASSEMBLY RH

a.

for Standard Roof:

i.
B543153C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw and clip.


ii.
B543154C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip, guide and claw.


iii.
B543155C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip and claw.


iv.
B543156C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


v.
B543157C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the clip and remove the rear quarter trim board assembly RH as shown in the illustration.


vi.

w/ USB Charger:

Disconnect the connector.



b.

for High Roof:

HINT:

Use the same procedure described for the LH side.



Hide 74617A 40.REMOVE ASSIST GRIP PLUG (w/ Assist Grip)

HINT:

Use the same procedure for both assist grip plugs.


a.
B519207

Insert moulding remover A at the position shown in the illustration, detach the claw and guide and remove the assist grip plug.


Hide 74680 41.REMOVE PILLAR ASSIST GRIP ASSEMBLY C (w/ Assist Grip)

a.
B519208

Remove the 2 bolts and pillar assist grip assembly C.


Hide 62610K 42.REMOVE SIDE TRIM BOARD ASSEMBLY RH (for High Roof)

a.
B532730C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip and claw.


b.
B532731C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip and claw.


c.
B532732C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place both hands at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


d.
B532733C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration, pull in the direction indicated by the arrow to detach the clip and remove the side trim board assembly RH.


Hide 62639A 43.REMOVE QUARTER PILLAR GARNISH LH

a.

for Standard Roof:

i.
B519260C02
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


ii.
B519262C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place both hands at the position shown in the illustration, pull in the direction indicated by the arrow to detach the clip and claw and remove the quarter pillar garnish LH.



b.

for High Roof:

i.
B519259C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


ii.
B519261C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place both hands at the position shown in the illustration, pull in the direction indicated by the arrow to detach the clip and claw and remove the quarter pillar garnish LH.



Hide 62639A 44.REMOVE QUARTER PILLAR GARNISH LH (for High Roof)

HINT:

Use the same procedure to remove the quarter pillar garnish LH the other side.


Hide 62638A 45.REMOVE QUARTER PILLAR GARNISH RH (for High Roof)

HINT:

Use the same procedure described for the LH side.


Hide 62412 46.REMOVE CENTER PILLAR GARNISH LH

a.
B539566

Remove the clip.


b.
B539567C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


c.
B539568C01
0,0 0,0 false
V113147

Remove in this Direction


Pull in the direction of the arrow shown in the illustration to detach the clip, claw and guide.


d.
B539569C01
0,0 0,0 false
V113147

Remove in this Direction


Pull in the direction of the arrow shown in the illustration to detach the clip and remove the center pillar garnish LH.


Hide 62638A 47.REMOVE QUARTER PILLAR GARNISH RH

a.

for Standard Roof:

i.
B539616C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


ii.
B539617C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place both hands at the position shown in the illustration, pull in the direction indicated by the arrow to detach the clip and claw and remove the quarter pillar garnish RH.



b.

for High Roof:

i.
B532734C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


ii.
B532735C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place both hands at the position shown in the illustration, pull in the direction indicated by the arrow to detach the clip and claw and remove the quarter pillar garnish RH.



Hide 72681E 48.REMOVE REAR SEAT HOOK (w/ Seat Hook)

HINT:

Use the same procedure for the other side.


a.
B541139

Loosen the screw.


b.

Detach the guide and remove the rear seat hook.


Hide 62472D 49.REMOVE REAR UPPER PILLAR GARNISH LH

a.

for Standard Roof:

i.
B519233C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


ii.
B519234C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


iii.
B519235C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration, pull in the direction indicated by the arrow to detach the clip and claw and remove the rear upper pillar garnish LH.



b.

for High Roof:

i.
B519236C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


ii.
B519237C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


iii.
B519238C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration, pull in the direction indicated by the arrow to detach the clip, claw and guide and remove the rear upper pillar garnish LH.



Hide 62471D 50.REMOVE REAR UPPER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 62460A 51.REMOVE REAR ROOF SIDE RAIL GARNISH ASSEMBLY LH

a.
B539602C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


for Standard Roof:

Place your hand at the position shown in the illustration, pull in the direction indicated by the arrow to detach the clip and remove the rear roof side rail garnish assembly LH.


b.

for High Roof:

i.
B539605

Disconnect the connector.


ii.
B539606C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration, pull in the direction indicated by the arrow to detach the clip and remove the rear roof side rail garnish assembly LH.



Hide 62450A 52.REMOVE REAR ROOF SIDE RAIL GARNISH ASSEMBLY RH

a.
B539604C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


for Standard Roof:

Place your hand at the position shown in the illustration, pull in the direction indicated by the arrow to detach the clip and remove the rear roof side rail garnish assembly LH.


b.

for High Roof:

HINT:

Use the same procedure described for the LH side.



Hide 62440D 53.REMOVE FRONT ROOF SIDE RAIL GARNISH ASSEMBLY LH

a.
B539603C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


for Standard Roof:

Place your hand at the position shown in the illustration, pull in the direction indicated by the arrow to detach the clip and remove the front roof side rail garnish assembly LH.


b.

for High Roof:

i.
B539608

Disconnect the connector.


ii.
B539609C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration, pull in the direction indicated by the arrow to detach the clip and remove the front roof side rail garnish assembly LH.



Hide 62430D 54.REMOVE FRONT ROOF SIDE RAIL GARNISH ASSEMBLY RH (for High Roof)

B539607C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


a.

Place both hands at the position shown in the illustration, pull in the direction indicated by the arrow to detach the clip and remove the front roof side rail garnish assembly RH.


Hide 81240 55.REMOVE NO. 1 ROOM LIGHT ASSEMBLY

Hide 81240D 56.REMOVE NO. 2 ROOM LIGHT ASSEMBLY (for High Roof, w/ No. 2 Room Light Assembly)

HINT:

Use the same procedure described for the No. 1 room light assembly.


Hide 63349A 57.REMOVE REAR ROOF HEADLINING GARNISH (w/ Roof Window Glass)

a.
B539596C01
0,0 0,0 false
V113147

Pull in this Direction


Insert moulding remover D at the position shown in the illustration.


b.
B539597C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand into the gap and pull as shown to detach the clip.


c.
B539598C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


d.
B539599C02
0,0 0,0 false
V113147

Remove in this Direction


Pull in the direction of the arrow shown in the illustration to detach the clip and remove the rear roof headlining garnish.


Hide 58.REMOVE REAR ROOF HEADLINING ASSEMBLY

a.

for Standard Roof:

i.
B539620C01
1.583,0.438 2,0.271 2,0.271 2.167,0.271 true 2.208,0.188 2.521,0.385 0.313,0.198 10 false *a
*a Plate
V100136

w/ Plate


Remove the 14 clips and 2 plates.

HINT:

The clips indicated by the white arrow have plates between the rear roof headlining assembly and body. Be careful not to let them fall.



ii.

Detach the guide and remove the rear roof headlining assembly.



b.

for High Roof:

i.

w/o Roof Window Glass:

Remove the 20 clips, 4 plates and rear roof headlining assembly.

HINT:

The clips indicated by the white arrow have plates between the rear roof headlining assembly and body. Be careful not to let them fall.


B539622C01
6.021,0.698 6.25,0.417 6.25,0.417 6.5,0.417 true 6.552,0.344 6.865,0.542 0.313,0.198 10 false *a
*a Plate - -
V100136

w/ Plate - -



ii.

w/ Roof Window Glass:

Remove the 22 clips, 4 plates and rear roof headlining assembly.

HINT:

The clips indicated by the white arrow have plates between the rear roof headlining assembly and body. Be careful not to let them fall.


B539623C01
6.042,0.708 6.333,0.25 6.333,0.25 6.5,0.25 true 6.552,0.177 6.865,0.375 0.313,0.198 10 false *a
*a Plate - -
V100136

w/ Plate - -




c.
B539621

Turn the rear roof headlining assembly diagonally and bend slightly to remove it from the back door.

NOTICE:
·

Make sure that wrinkles do not form in the rear roof headlining assembly during removal.

·

Make sure that the rear roof headlining assembly does not get caught on anything as it may become bent or damaged.

·

Do not damage the rear roof headlining assembly or vehicle interior.

·

2 or more people are required when carrying the rear roof headlining assembly out of the vehicle, as it may become deformed.




Hide 87834 59.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER

Hide 81260A 60.REMOVE MAP LIGHT ASSEMBLY

Hide 86466D 61.REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Pre-collision System)

Hide 86768 62.REMOVE ROOF ANTENNA COVER (w/ Digital Audio Broadcasting Antenna)

a.
B539574C01
0,0 0,0 false
V113147

Remove in this Direction


Pull in the direction of the arrow shown in the illustration to detach the clip and remove the roof antenna cover.


Hide 63.REMOVE ASSIST GRIP ASSEMBLY (w/ Assist Grip)

HINT:

Use the same procedure for all assist grip assemblies.


a.
B539610C01
1.479,3.083 1.896,3.083 true 2.156,0.552 2.573,0.552 true 1.167,3 1.552,3.188 0.385,0.188 10 true SST 2.531,0.458 2.729,0.698 0.198,0.24 10 true *a
*a Cutout


Insert SST into the cutout of the assist grip cover LH as shown in the illustration.

SST
09813-00010  

NOTICE:

To prevent the assist grip assembly from being damaged, make sure to insert SST straight into the cutout.



b.
B539611C01
2.531,1.833 2.75,2.021 0.219,0.188 10 true *a
*a 30 to 45°
V113147

Remove in this Direction


Pull SST as shown in the illustration to detach the claw.

NOTICE:

To prevent the assist grip assembly from being damaged, make sure to only pull SST as shown in the illustration.


HINT:

Use the same procedure for the claw on the other side of the assist grip cover LH.



c.

Remove the assist grip cover LH.

HINT:

Use the same procedure for the LH side and RH side.



d.
B539612

Pinch the clip with needle-nose pliers.

HINT:

Use the same procedure for both clips.



e.
B539613C01
0,0 0,0 false
V113147

Remove in this Direction


Hold the handle and pull in the direction indicated by the arrow shown in the illustration to remove the assist grip assembly.


f.

Using needle-nose pliers, remove the clip.


Hide 74320 64.REMOVE VISOR ASSEMBLY LH

a.
B539575

Remove the 2 screws.


b.
B539576C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Pull in the direction (1) shown in the illustration to disconnect the visor assembly LH from the visor holder.


c.

Pull in the direction (2) shown in the illustration to remove the visor assembly LH.


Hide 74310 65.REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 74348 66.REMOVE VISOR HOLDER

HINT:

Use the same procedure for the opposite side.


a.
B539585C01
2.375,0.667 2.708,0.667 true 2.719,0.583 2.938,0.76 0.219,0.177 10 true *a
*a 45°
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Turn the visor holder end approximately 45° in the direction (1) indicated by the arrow shown in the illustration, and pull it out in the direction (2) indicated by the arrow.


b.
B539586

Detach the claw and remove the visor holder base.


Hide 53989A 67.REMOVE AIR INTAKE NET

HINT:

Use the same procedure for the opposite side.


a.
B539594C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and pull in the direction of the arrow shown in the illustration.


b.
B539595C01
0,0 0,0 false
V113147

Remove in this Direction


Pull in the direction of the arrow shown in the illustration to detach the guide and remove the air intake net.


Hide 65896J 68.REMOVE COVER TOP SET BOLT CAP (for Standard Roof)

a.
B539627C01
0,0 0,0 false
V113147

Remove in this Direction


Insert moulding remover A at the position shown in the illustration, detach the claw and guide and remove the cover top set bolt cap.


Hide 63438F 69.REMOVE NO. 1 INNER ROOF RACK COVER (for High Roof)

HINT:

Use the same procedure for the opposite side.


a.
B539587C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape at the position shown in the illustration.


b.
B539588

Insert moulding remover B at the position shown in the illustration, detach the claw and guide and remove the No. 1 inner roof rack cover.


Hide 63439D 70.REMOVE NO. 2 INNER ROOF RACK COVER (for High Roof)

HINT:

Use the same procedure for the opposite side.


a.
B539589C01
0,0 0,0 false
V113147

Remove in this Direction


Insert moulding remover B at the position shown in the illustration, detach the claw and guide and remove the No. 2 inner roof rack cover.


Hide 63413C 71.REMOVE FRONT INNER ROOF RACK BOARD (for High Roof)

a.

Remove the 6 bolts.

B539590


b.
B539591

Using a clip remover, detach the clip.


c.

Pull in the direction of the arrow shown in the illustration to detach the guide and clip.

B539592C01
0,0 0,0 false
V113147

Remove in this Direction - -



d.
B539593C01
0,0 0,0 false
V113146

Press Here with Finger


Press the hook in the illustration with your finger and remove the front inner roof rack board.


Hide 72.REMOVE ROOF HEADLINING ASSEMBLY (for Standard Roof)

a.

for Windshield Glass Side:

i.

Disconnect each connector.



b.

for Front Pillar LH Side:

i.

w/ Curtain Shield Airbag:

Remove the protective cover installed to the front pillar LH.


ii.
B539624C02
2.604,1.198 2.875,1.427 0.271,0.229 12 true *A
*A w/ Rear Wiper or w/ Digital Inner Mirror
V100135

Connector
V100136

Washer Hose


Disconnect the 3 connectors.


iii.

Using a clip remover, detach the wire harness clamp.


iv.

w/ Rear Wiper or w/ Digital Inner Mirror:

Disconnect the washer hose.


v.

w/ Curtain Shield Airbag:

Install the protective cover to the front pillar LH.



c.

for Rear Roof LH Side:

i.
B539625C01
0.479,1.708 0.76,1.948 0.281,0.24 12 true *A
*A w/ Rear Wiper or w/ Digital Inner Mirror
V100135

Connector
V100136

Washer Hose


Disconnect the connector.


ii.

w/ Rear Wiper or w/ Digital Inner Mirror:

Disconnect the washer hose.



d.

for Rear Roof RH Side, w/ Digital Inner Mirror:

i.
B539626

Detach the clamp and disconnect the connector.



e.

Remove the 5 bolts.

B539628


f.

Remove the 10 clips and 2 plates.

HINT:

The clips indicated by the white arrow have plates between the roof headlining assembly and body. Be careful not to let them fall.



g.

Detach the fastener and remove the roof headlining assembly.

B539636C02
6,1.583 6.167,1.25 6.167,1.25 6.417,1.25 false 6.031,0.094 6.344,0.292 0.313,0.198 10 false *a 6.469,1.177 6.781,1.375 0.313,0.198 10 false *b
*a Fastener *b Plate
V100136

w/ Plate - -



h.
B539638

Turn the roof headlining assembly diagonally and bend slightly to remove it from the back door.

NOTICE:
·

Make sure that wrinkles do not form in the roof headlining assembly during removal.

·

Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

·

Do not damage the roof headlining assembly or vehicle interior.

·

2 or more people are required when carrying the roof headlining assembly out of the vehicle, as it may become deformed.




Hide 73.REMOVE ROOF HEADLINING ASSEMBLY (for High Roof)

a.

for Windshield Glass Side:

i.

Disconnect each connector.



b.

for Front Pillar LH Side:

i.

w/ Curtain Shield Airbag:

Remove the protective cover installed to the front pillar LH.


ii.
B539629C03
2.74,1.26 3.021,1.49 0.281,0.229 12 true *A
*A w/ Rear Wiper or w/ Digital Inner Mirror
V100135

Connector
V100136

Washer Hose


Disconnect the 3 connectors.


iii.

Using a clip remover, detach the wire harness clamp.


iv.

w/ Rear Wiper or w/ Digital Inner Mirror:

Disconnect the washer hose.


v.

w/ Curtain Shield Airbag:

Install the protective cover to the front pillar LH.



c.

for Rear Roof LH Side:

i.
B539630

Disconnect the connector.


ii.

w/ Rear Wiper or w/ Digital Inner Mirror:

Detach the clamp and disconnect the washer hose.

B539631



d.

for Rear Roof RH Side, w/ Digital Inner Mirror:

i.

Detach the clamp and disconnect the connector.

B539637



e.

for Roof Headlining Front Side:

i.
B539632

w/o Wire Harness Protector:

Detach the clamp.


ii.
B539650

w/ Wire Harness Protector:

Detach the clamp.



f.
B539633

Remove the 4 bolts.


g.

Remove the 14 clips, 2 plates and roof headlining assembly.

HINT:

The clips indicated by the white arrow have plates between the roof headlining assembly and body. Be careful not to let them fall.


B539634C01
6,1.083 6.167,0.75 6.167,0.75 6.333,0.75 true 6.448,0.625 6.76,0.823 0.313,0.198 10 false *a
*a Plate - -
V100136

w/ Plate - -



h.
B539635

Turn the roof headlining assembly diagonally and bend slightly to remove it from the back door.

NOTICE:
·

Make sure that wrinkles do not form in the roof headlining assembly during removal.

·

Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

·

Do not damage the roof headlining assembly or vehicle interior.

·

2 or more people are required when carrying the roof headlining assembly out of the vehicle, as it may become deformed.