The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during instrument panel safety pad removal/installation are shown below.
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the systems is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1. BOLTS, SCREWS AND NUTS TABLE
All bolts, screws and clips relevant to installing and removing the instrument panel are shown along with their alphabetic code in the table below.
2. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
for Type A:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>PRECAUTION
for Type B:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type B)>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for 7GR-FKS:
for 1GD-FTV:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
67912A
4.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE LH
67914B
5.REMOVE FRONT DOOR SCUFF PLATE LH
62112
6.REMOVE COWL SIDE TRIM BOARD LH
Remove the cap nut.
|
Remove in this Direction |
Detach the clip, claw and guide and remove the cowl side trim board LH.
55631A
7.REMOVE NO. 1 INSTRUMENT PANEL UNDER TRAY STOPPER
Remove the No. 1 instrument panel under tray stopper.
55011A
8.REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY
|
Screw <A> |
Remove the screw <A>.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw and guide.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw and remove the No. 1 instrument panel garnish sub-assembly.
w/ Power Slide Door:
Disconnect each connector.
55318C
9.REMOVE INSTRUMENT SIDE PANEL LH
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw and guide.
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration to detach the guide and remove the instrument side panel LH.
55641
10.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER
for LHD:
|
Screw <A> |
Remove the 3 screws <A>.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw.
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration to detach the clip and claw.
|
Remove in this Direction |
Pull in the direction indicated by the arrow to detach the guide and remove the No. 1 instrument panel under cover.
w/ Tire Pressure Warning System:
Disconnect the connector.
for RHD:
|
Screw <A> |
Remove the 3 screws <A>.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw.
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration to detach the clip and claw.
|
Remove in this Direction |
Pull in the direction indicated by the arrow to detach the guide and remove the No. 1 instrument panel under cover.
53601
11.REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Detach the claw in the direction (1) indicated by the arrow shown in the illustration.
Detach the guide in the direction (2) indicated by the arrow shown in the illustration and remove the hood lock control lever sub-assembly.
77306
12.REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Detach the claw in the direction (1) indicated by the arrow shown in the illustration.
Detach the guide in the direction (2) indicated by the arrow shown in the illustration and remove the fuel lid lock open lever sub-assembly.
55432D
13.REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
|
Screw <A> |
Remove the 2 screws <A>.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw and remove the lower No. 1 instrument panel finish panel.
Disconnect each connector.
55044C
14.REMOVE INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
|
Protective Tape |
Apply protective tape as shown in the illustration.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw and remove the instrument panel finish panel sub-assembly.
55433B
15.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL
|
Screw <A> |
Remove the screw <A>.
Using moulding remover A, detach the claw.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw and guide and remove the lower No. 2 instrument panel finish panel.
|
Connector |
|
Aspirator Hose |
for Automatic Air Conditioning System:
Disconnect the connector and aspirator hose.
55445B
16.REMOVE INSTRUMENT PANEL FINISH PLATE (w/o Knee Airbag)
|
Remove in this Direction |
Pull in the direction indicated by the arrow to detach the claw and remove the instrument panel finish plate.
55313
17.REMOVE LOWER INSTRUMENT PANEL LH (w/o Knee Airbag)
|
Bolt <E> |
Remove the 3 bolts <E>.
Detach the guide and remove the lower instrument panel LH.
73900
18.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)
67911B
19.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE RH
Use the same procedure described for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL
67913B
20.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL
62111C
21.REMOVE COWL SIDE TRIM BOARD RH
Remove the cap nut.
|
Remove in this Direction |
Detach the clip, claw and guide and remove the cowl side trim board RH.
55632B
22.REMOVE NO. 2 INSTRUMENT PANEL UNDER TRAY SUPPORT
Remove the No. 2 instrument panel under tray support.
55012A
23.REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY
|
Screw <A> |
Remove the screw <A>.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw and guide and remove the No. 2 instrument panel garnish sub-assembly.
55317A
24.REMOVE INSTRUMENT SIDE PANEL RH
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw and guide.
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration to detach the guide and remove the instrument side panel RH.
55642
25.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER
|
Remove in this Direction |
Detach the claw and lower the No. 2 instrument panel under cover in the direction of the arrow shown in the illustration.
|
Remove in this Direction |
Pull in the direction of the arrow shown in the illustration to detach the guide and remove the No. 2 instrument panel under cover.
55312
26.REMOVE LOWER INSTRUMENT PANEL
|
Slide in this Direction |
Open the glove compartment door and slide the instrument panel box lock knob in the direction of the arrow shown in the illustration.
|
Remove in this Direction |
Push in the direction of the arrow shown in the illustration to detach the clip.
|
Remove in this Direction |
Pull in the direction of the arrow shown in the illustration to detach the guide and remove the lower instrument panel.
55438A
27.REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL RETAINER
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration, pull in the direction indicated by the arrow to detach the claw and remove the No. 2 instrument panel finish panel retainer.
28.REMOVE FRONT CONSOLE BOX (w/ Console Tray)
58533C
29.REMOVE CENTER FLOOR CARPET COVER RH
|
Protective Tape |
for LHD:
Apply protective tape as shown in the illustration.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration, pull in the direction indicated by the arrow to detach the clip, claw and guide and remove the center floor carpet cover RH.
for RHD:
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration, pull in the direction indicated by the arrow to detach the clip, claw and guide and remove the center floor carpet cover RH.
58534E
30.REMOVE CENTER FLOOR CARPET COVER LH
for LHD:
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw.
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration to detach the claw.
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration to detach the guide and remove the center floor carpet cover LH.
for RHD:
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw.
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration to detach the claw.
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration to detach the guide and remove the center floor carpet cover LH.
55646
31.REMOVE NO. 3 INSTRUMENT PANEL UNDER COVER
w/o Console Tray:
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip and claw.
|
Remove in this Direction |
Detach the clip and claw and remove the No. 3 instrument panel under cover.
Disconnect each connector.
w/ Console Tray:
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip and claw.
|
Remove in this Direction |
Detach the clip and claw and remove the No. 3 instrument panel under cover.
Disconnect each connector.
33504F
32.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission)
|
Remove in this Direction |
Twist the shift lever knob sub-assembly in the direction indicated by the arrow and remove it.
33622
33.DISCONNECT NO. 1 SHIFT LEVER KNOB COVER (for Automatic Transmission)
33504F
34.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transmission)
58840Q
35.REMOVE SHIFTING HOLE COVER ASSEMBLY (for Manual Transmission)
for Semi-trim:
|
Place Hands Here |
|
Remove in this Direction |
Place both hands at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw.
|
Place Hands Here |
|
Remove in this Direction |
Pull in the direction indicated by the arrow to detach the claw and remove the shifting hole cover assembly.
for Full-trim:
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw.
|
Remove in this Direction |
Pull in the direction indicated by the arrow to detach the claw and remove the shifting hole cover assembly.
35970F
36.REMOVE POSITION INDICATOR HOUSING ASSEMBLY (for Automatic Transmission)
for Semi-trim:
|
Protective Tape |
Apply protective tape as shown in the illustration.
|
Remove in this Direction |
Using moulding remover B, pull in the direction indicated by the arrow as shown in the illustration.
Using moulding remover A, insert in the gap as shown in the illustration to detach the clip.
|
Remove in this Direction |
Using moulding remover A, pull in the direction indicated by the arrow to detach the claw and remove the position indicator housing assembly.
Disconnect the connector.
for Full-trim:
|
Protective Tape |
Apply protective tape as shown in the illustration.
|
Remove in this Direction |
Using moulding remover B, pull in the direction indicated by the arrow as shown in the illustration.
Using moulding remover A, insert in the gap as shown in the illustration to detach the clip.
|
Remove in this Direction |
Pull in the direction indicated by the arrow to detach the claw and remove the position indicator housing assembly.
Disconnect the connector.
55405B
37.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)
for Semi-trim:
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw and remove the center instrument cluster finish panel sub-assembly.
|
Place Hands Here |
|
Remove in this Direction |
Place both hands at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw and remove the center instrument cluster finish panel sub-assembly.
Disconnect each connector.
|
Protective Tape |
Detach the guide.
Using a thin-bladed screwdriver, detach the claw and remove the No. 2 heater control cable sub-assembly and air mix damper control cable sub-assembly.
Tape the thin-bladed screwdriver tip before use.
for Full-trim:
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw in the order shown in the illustration.
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw.
When removing forcibly, do not pull excessively.
If excessive force is applied to the center instrument cluster finish panel sub-assembly, it may become damaged.
|
Remove in this Direction |
Place your hand in the gap, pull in the direction indicated by the arrow shown in the illustration, detach the claw and remove the center instrument cluster finish panel sub-assembly.
Disconnect each connector.
|
Protective Tape |
Detach the guide.
Using a thin-bladed screwdriver, detach the claw and remove the No. 2 heater control cable sub-assembly and air mix damper control cable sub-assembly.
Tape the thin-bladed screwdriver tip before use.
55900
38.REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw and remove the air conditioning control assembly.
|
Place Hands Here |
|
Remove in this Direction |
Place both hands at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw and remove the air conditioning control assembly.
Disconnect each connector.
55410C
39.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration to detach the claw and remove the instrument cluster finish panel assembly.
40.REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (for Radio Receiver Type)
41.REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)
42.REMOVE DISPLAY AND NAVIGATION ASSEMBLY WITH BRACKET (w/ Navigation System)
43.REMOVE RADIO TUNER OPENING COVER WITH BRACKET (w/ Radio Receiver Opening Cover)
Remove the 2 bolts.
Remove the 2 bolts.
|
Remove in this Direction |
Detach the guide and remove the radio tuner opening cover with bracket.
55434B
44.REMOVE CENTER LOWER INSTRUMENT PANEL FINISH PANEL
for Semi-trim:
|
Bolt <B> |
Remove the bolt <B>.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw and guide.
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration to detach the claw.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration, pull in the direction indicated by the arrow to detach the claw and remove the center lower instrument panel finish panel.
for Full-trim:
|
Bolt <B> |
Remove the bolt <B>.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw and guide.
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration to detach the claw and remove the center lower instrument panel finish panel.
55320
45.REMOVE LOWER NO. 2 INSTRUMENT PANEL ASSEMBLY
Open the glove compartment door assembly.
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw and remove the instrument panel box door knob.
Tape the thin-bladed screwdriver tip before use.
|
Bolt <B> |
Remove the 5 bolts <B>.
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration to detach the claw and remove the lower No. 2 instrument panel assembly.
55414A
46.REMOVE INSTRUMENT CLUSTER FINISH PANEL END (for Semi-trim)
|
Place Hands Here |
|
Remove in this Direction |
Place both hands at the position shown in the illustration, pull in the direction indicated by the arrow to detach the claw and remove the instrument cluster finish panel end.
55413D
47.REMOVE CENTER LOWER INSTRUMENT CLUSTER FINISH PANEL
for Semi-trim:
|
Place Hand Here |
0,0 0,0
false
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration, pull in the direction indicated by the arrow to detach the claw and remove the center lower instrument cluster finish panel.
for Full-trim:
|
Place Hands Here |
|
Remove in this Direction |
Place both hands at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw.
|
Place Hands Here |
|
Remove in this Direction |
Place both hands at the position shown in the illustration, pull in the direction indicated by the arrow to detach the claw and remove the center lower instrument cluster finish panel.
55404E
48.REMOVE UPPER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
|
Remove in this Direction |
Using moulding remover A, pull in the direction indicated by the arrow shown in the illustration to detach the claw.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw.
|
Remove in this Direction |
Using moulding remover B, detach the claw and guide.
|
Remove in this Direction |
Using moulding remover B, detach the claw and guide.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration, detach the claw and guide and remove the upper instrument cluster finish panel sub-assembly.
83100
49.REMOVE COMBINATION METER ASSEMBLY
55670
50.REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration, pull in the direction indicated by the arrow to detach the claw and remove the No. 3 instrument panel register assembly.
Disconnect the connector.
55680A
51.REMOVE NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration, pull in the direction indicated by the arrow to detach the claw and remove the No. 4 instrument panel register assembly.
55446A
52.REMOVE NO. 1 SWITCH HOLE BASE
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration, pull in the direction indicated by the arrow to detach the claw and remove the No. 1 switch hole base.
55447C
53.REMOVE NO. 2 SWITCH HOLE BASE
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration, pull in the direction indicated by the arrow to detach the claw and remove the No. 2 switch hole base.
Disconnect each connector.
55476A
54.REMOVE NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration, pull in the direction indicated by the arrow to detach the claw and guide and remove the No. 3 instrument cluster finish panel garnish.
55314A
55.REMOVE CENTER LOWER INSTRUMENT PANEL (for Semi-trim)
|
Screw <C> |
Remove the screw <C>.
for Automatic Transmission:
|
Place Hands Here |
|
Remove in this Direction |
Place both hands at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw.
|
Place Hands Here |
|
Remove in this Direction |
Place both hands at the position shown in the illustration, pull in the direction indicated by the arrow to detach the claw and remove the center lower instrument panel.
for Manual Transmission:
|
Place Hands Here |
|
Remove in this Direction |
Place both hands at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw.
|
Place Hands Here |
|
Remove in this Direction |
Place both hands at the position shown in the illustration, pull in the direction indicated by the arrow to detach the claw and remove the center lower instrument panel.
55314A
56.REMOVE CENTER LOWER INSTRUMENT PANEL (for Full-trim)
|
Screw <C> |
Remove the screw <C>.
for Automatic Transmission:
|
Place Hands Here |
|
Remove in this Direction |
Place both hands at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw.
|
Place Hands Here |
|
Remove in this Direction |
Place both hands at the position shown in the illustration, pull in the direction indicated by the arrow to detach the claw and remove the center lower instrument panel.
for Manual Transmission:
|
Place Hands Here |
|
Remove in this Direction |
Place both hands at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw.
|
Place Hands Here |
|
Remove in this Direction |
Place both hands at the position shown in the illustration, pull in the direction indicated by the arrow to detach the claw and remove the center lower instrument panel.
62312B
57.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Remove the front door opening trim weatherstrip LH from the area shown in the illustration.
62311B
58.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
74680
59.REMOVE PILLAR ASSIST GRIP ASSEMBLY LH
74680
60.REMOVE PILLAR ASSIST GRIP ASSEMBLY RH
Use the same procedure described for the LH side.
62212
61.REMOVE FRONT PILLAR GARNISH LH
62211
62.REMOVE FRONT PILLAR GARNISH RH
Use the same procedure described for the LH side.
63.REMOVE TRANSMISSION INSTRUMENT PANEL SHIFT ASSEMBLY (for Automatic Transmission)
55301
64.REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
for LHD:
| *A | w/ Solar Sensor |
| *B | w/ Front Passenger Airbag |
| *C | w/ Parking Assist Monitor System |
Disconnect each connector.
Disconnect the connector and detach the clamp.
w/ Telematics Transceiver:
Disconnect the connector.
|
Remove in this Direction |
Detach the claw and remove the connector holder.
Detach the claw and remove the DLC3.
|
Bolt <D> |
Remove the 2 bolts <D>.
Remove the 7 bolts <B>, nut <G> and 2 clips <F>.
|
Bolt <B> |
|
Nut <G> |
|
Clip <F> | - | - |
Pull in the direction indicated by the arrow shown in the illustration, detach the guide and remove the instrument panel sub-assembly.
|
Remove in this Direction | - | - |
|
Remove in this Direction |
Remove the instrument panel sub-assembly from the front door as shown in the illustration.
for RHD:
| *A | w/ Solar Sensor or w/ Blind Spot Monitor System |
| *B | w/ Front Passenger Airbag |
| *C | w/ Parking Assist Monitor System |
Disconnect each connector.
Disconnect the connector and detach the clamp.
Detach the claw and remove the DLC3.
|
Bolt <D> |
Remove the 2 bolts <D>.
Remove the 7 bolts <B>, nut <G> and 2 clips <F>.
|
Bolt <B> |
|
Nut <G> |
|
Clip <F> | - | - |
Pull in the direction indicated by the arrow shown in the illustration, detach the guide and remove the instrument panel sub-assembly.
|
Remove in this Direction | - | - |
|
Remove in this Direction |
Remove the instrument panel sub-assembly from the front door as shown in the illustration.