Home › Drivetrain › CLUTCH › CLUTCH MASTER CYLINDER › 2019.02–2019.06
RM35X0E _52 Drivetrain _078837 CLUTCH _0382377 CLUTCH MASTER CYLINDER A

CLUTCH  CLUTCH MASTER CYLINDER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during clutch master cylinder assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the systems is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 67912A 3.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE LH

Hide 67914B 4.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112 5.REMOVE COWL SIDE TRIM BOARD LH

Hide 55631A 6.REMOVE NO. 1 INSTRUMENT PANEL UNDER TRAY STOPPER (for LHD)

Hide 55011A 7.REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY (for LHD)

Hide 55318C 8.REMOVE INSTRUMENT SIDE PANEL LH

Hide 55641 9.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER

Hide 55432D 10.REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL (for LHD)

Hide 55433B 11.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

Hide 73900 12.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 55445B 13.REMOVE INSTRUMENT PANEL FINISH PLATE (w/o Driver Side Knee Airbag)

Hide 55313 14.REMOVE LOWER INSTRUMENT PANEL LH (w/o Driver Side Knee Airbag)

Hide 15.DRAIN CLUTCH FLUID

NOTICE:

Wash brake fluid off immediately if it adheres to any painted surface.


Hide 31481K 16.LOOSEN CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE

C413764

a.

Using a union nut wrench, loosen the clutch master cylinder to flexible hose tube.

HINT:

Use a container to collect the fluid.



Hide 31453A 17.REMOVE CLUTCH MASTER CYLINDER PUSH ROD CLEVIS WITH HOLE PIN

Hide 31434 18.DISCONNECT CLUTCH RESERVOIR TUBE

C410528

a.

Slide the hose clip and disconnect the clutch reservoir tube from the clutch master cylinder assembly.

HINT:

Use a container to collect the fluid.



Hide 31481K 19.DISCONNECT CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE

C413764

a.

Using a union nut wrench, disconnect the clutch master cylinder to flexible hose tube.

HINT:

Use a container to collect the fluid.



Hide 31410 20.REMOVE CLUTCH MASTER CYLINDER ASSEMBLY

a.
C410545

Remove the 2 nuts.


b.
C410541C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the clutch master cylinder assembly from the vehicle body.


c.

for RHD with master cylinder bracket:

i.
C410617C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the clutch master cylinder assembly and master cylinder bracket from the vehicle body.



Hide 31415 21.REMOVE CLUTCH MASTER CYLINDER GASKET

C410542

a.

Remove the clutch master cylinder gasket from the clutch master cylinder assembly.


b.

for RHD with master cylinder bracket:

i.
C410615

Remove the 2 clutch master cylinder gaskets and master cylinder bracket from the clutch master cylinder assembly.