1.INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY
for 1GD-FTV:
Install the clutch release cylinder assembly with the 2 bolts.
Install the wire harness clamp bracket with the 2 nuts.
Engage the clamp and connect the No. 2 engine wire.
for 7GR-FKS:
Install the clutch release cylinder assembly with the 2 bolts.
31482D
2.CONNECT CLUTCH RELEASE CYLINDER TO ACCUMULATOR TUBE (for 7GR-FKS)
| *a | Torque Wrench Fulcrum Length |
Using a union nut wrench, connect the clutch release cylinder to accumulator tube.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)
31482
3.CONNECT CLUTCH RELEASE CYLINDER TO FLEXIBLE HOSE TUBE (for 1GD-FTV)
| *a | Torque Wrench Fulcrum Length |
Using a union nut wrench, connect the clutch release cylinder to flexible hose tube.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)
31349
4.INSTALL CLUTCH CABLE HEAT INSULATOR (for 7GR-FKS)
5.INSTALL CLUTCH ACCUMULATOR HEAT INSULATOR (for 7GR-FKS)
6.BLEED AIR FROM CLUTCH PIPE LINE
Click hereDrivetrain>CLUTCH>CLUTCH SYSTEM>BLEEDING
7.CHECK FOR CLUTCH FLUID LEAKAGE
Check for leaks in the clutch system.
8.CHECK FLUID LEVEL IN RESERVOIR
51773E
9.INSTALL STEP PLATE COVER RH (w/ Cover)
for 7GR-FKS:
Click hereEngine / Hybrid System>7GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
for 1GD-FTV:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
51408B
10.INSTALL ENGINE UNDER COVER SUB-ASSEMBLY RH (for 1GD-FTV, w/ Cover)
51495
11.INSTALL TRANSMISSION UNDER COVER (for 1GD-FTV, w/ Cover)
51407A
12.INSTALL NO. 3 ENGINE UNDER COVER SUB-ASSEMBLY (for 7GR-FKS, w/ No. 3 Engine Under Cover Sub-assembly)
51405A
13.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
for 7GR-FKS:
Click hereEngine / Hybrid System>7GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
for 1GD-FTV:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
52618
14.INSTALL LOWER FRONT BUMPER ABSORBER
for 7GR-FKS:
Click hereEngine / Hybrid System>7GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
for 1GD-FTV:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
51406A
15.INSTALL NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 2 Engine Under Cover Sub-assembly)
for 7GR-FKS:
Click hereEngine / Hybrid System>7GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
for 1GD-FTV:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION