The ECM controls the internal fuel pressure of the common rail assembly by opening and closing the pressure discharge valve. When sudden deceleration occurs, the internal fuel pressure will temporarily become higher than usual and combustion noise may result. Therefore the ECM will open the valve temporarily to discharge the excess pressure inside the common rail assembly. Also, the pressure discharge valve opens when the ignition switch is turned off to allow prompt discharge of the common rail internal pressure and so that the engine stops smoothly.
For more information on the pressure discharge valve and common rail system, refer to System Description (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>SYSTEM DESCRIPTION).
If DTC P127112, P127114 and/or P127273 is present, refer to the DTC chart for the fuel system (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>SYSTEM DESCRIPTION).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P127112 | Pressure Discharge Valve Circuit Short to Battery | Short in pressure discharge valve circuit for 0.5 seconds (2 trip detection logic). | ·
Short in pressure discharge valve circuit ·
Pressure discharge valve (common rail assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P1274 |
| P127114 | Pressure Discharge Valve Circuit Short to Ground or Open | Open in pressure discharge valve circuit for 0.5 seconds (2 trip detection logic). | ·
Open in pressure discharge valve circuit ·
Pressure discharge valve (common rail assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P1273 |
| P127273 | Pressure Discharge Valve Actuator Stuck Closed | The fuel pressure does not decrease while the engine is running (1 trip detection logic). | ·
Open or short in pressure discharge valve circuit (P127112 or P127114 is stored simultaneously) ·
Pressure discharge valve (common rail assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P1272 |
| DTC No. | Data List |
|---|---|
| P127112
P127114 P127273 |
·
Fuel Pressure (High) ·
Target Fuel Pressure (High) |
After confirming DTC P127112, P127114 and/or P127273, check the fuel pressure inside the common rail by entering the following menus: Powertrain / Engine / Data List / Fuel Pressure (High).
DTC P127112:
After clearing the DTC, drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal. Check that P127112 is not output.
DTC P127114:
After clearing the DTC, drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal. Check that P127114 is not output.
DTC P127273:
After clearing the DTC, perform the following procedure 5 times, and then check that P127273 is not output: Drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal.
| Engine Speed | Fuel Pressure (kPag) |
|---|---|
| Idling | Fuel Pressure (High) is within 5000 kPag of Target Fuel Pressure (High) |
| 3000 rpm (No engine load) |
| Condition | Fuel Pressure (High) (Idling) | Fuel Pressure (High) (1 Second after Engine Stopped) |
|---|---|---|
| Pressure discharge valve normal | 35000 kPag | 500 kPag |
| Open in pressure discharge valve circuit | 35000 kPag | 30000 kPag |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P127112
P127114 |
Drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal. |
| P127273 | Drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal. Perform this 5 times. |
This DTC is output when there is an open or short circuit in the pressure discharge valve circuit. When this DTC is output, the ECM enters fail-safe mode and restricts the engine output. The ECM stays in fail-safe mode until the ignition switch is turned off.
The pressure discharge valve opens when the common rail target fuel pressure decreases during deceleration, decreasing the fuel pressure in the common rail assembly. The ECM compares the speed that the fuel pressure decreases with the speed that the common rail target fuel pressure decreases.
When the ECM determines that the decreasing rate of the fuel pressure is smaller than the common rail target fuel pressure, the ECM determines that the valve is stuck closed or there is a fuel supply pump assembly malfunction (overpressure) and outputs this DTC.
When this DTC is output, the ECM enters fail-safe mode and restricts the engine output. The ECM stays in fail-safe mode until the ignition switch is turned off.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
After completing repairs, confirm that DTC P127112, P127114 and/or P127273 do not recur.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 5 times.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
| Result | Proceed to |
|---|---|
| DTC P127273 is output | A |
| DTC P127112 or P127114 is output | B |
| DTC P127112 or P127114 and P127273 are output | |
| Other DTCs are output | C |
A
B
C
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine / Utility / Pressure Discharge Valve Check.
| Tester Display |
|---|
| Pressure Discharge Valve Check |
Select "Close to Open Check".
Read the value of "Open and Engine OFF".
0.5 MPa or less
When the system is normal, the value of "Open and Engine OFF" should be at or close to 0 MPa.
When the fuel pressure value of "Open and Engine OFF" does not become equal to or less than 0.5 MPa, the pressure discharge valve may be stuck closed.
When the fuel pressure values of "Close and Engine OFF" and "Open and Engine OFF" are both 0 MPa, the pressure discharge valve may be stuck open or there may be a fuel leak.
Perform "Always Closed Check" if the value is not 0 MPa when the pressure discharge valve is open during "Close to Open Check". If the results are the same as during "Close to Open Check", there is a pressure discharge valve operation malfunction.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by releasing the accelerator pedal. Perform this 5 times.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTC.
| Result | Proceed to |
|---|---|
| DTC P127273 is output | A |
| No DTC is output | B |
A
B
Replace the fuel supply pump assembly.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal. Perform this 5 times.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P127112, P127114 and/or P127273.
Check the DTC judgment result.
If STATUS is INCOMPLETE, perform the following procedure 5 times: drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the common rail assembly.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>COMMON RAIL>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Inspect the common rail assembly.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>COMMON RAIL>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the pressure discharge valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E106-2 (COM3) - E6-2 (PRV+) | Always | Below 1 Ω |
| E106-1 (RLV) - E6-1 (PRV-) | Always | Below 1 Ω |
| E106-2 (COM3) or E6-2 (PRV+) - Body ground and other terminals | Always | 10 kΩ or higher |
| E106-1 (RLV) or E6-1 (PRV-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 5 times.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If no pending DTCs are output, proceed to the next step to check "All Readiness".
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P127112, P127114 and/or P127273.
Check the DTC judgment result.
| GTS Display | Result | Proceed to |
|---|---|---|
| Pending DTC | DTC P127112, P127114 and/or P127273 is output | B |
| All Readiness | NORMAL | A |
| ABNORMAL | B |
If STATUS is INCOMPLETE, perform the following procedure 5 times: drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal.
A
B
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT