Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2019.02–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0382589 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P203A12  Reductant Level Sensor Circuit High Circuit Short to Battery  P203A14  Reductant Level Sensor Circuit Low Circuit Short to Ground or Open  


DESCRIPTION

The urea pump has a level sensor that detects the position of the surface of the fluid inside the urea tank in order to measure the remaining quantity of urea solution.

When the remaining quantity of urea solution falls below a fixed value, a warning is displayed on the combination meter.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P203A12 Reductant Level Sensor Circuit High Circuit Short to Battery An open or short in the level sensor (urea pump) circuit for 3 seconds or more (1 trip detection logic).
·

Open or short in the level sensor circuit

·

Level sensor (urea pump)

·

ECU


Comes on DTC stored SAE Code: P203D
P203A14 Reductant Level Sensor Circuit Low Circuit Short to Ground or Open An open or short in the level sensor (urea pump) circuit for 3 seconds or more (1 trip detection logic).
·

Open or short in the level sensor circuit

·

Level sensor (urea pump)

·

ECU


Comes on DTC stored SAE Code: P203C

Related Data List
DTC No. Data List
P203A12
P203A14
Reductant Level

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P203A12
P203A14
Ignition switch to ON for 3 seconds or more

WIRING DIAGRAM

A357972E08
1.375,0.438 1.99,0.635 0.615,0.198 10 false VLV1 1.479,1.01 1.938,1.208 0.458,0.198 10 false LV1 1.385,1.552 2,1.75 0.615,0.198 10 false ELV1 0.406,2.052 0.719,2.25 0.313,0.198 10 false x4 0.406,2.229 4.073,2.427 3.667,0.198 10 false Level Sensor (Urea Pump) 5.688,0.458 6.302,0.656 0.615,0.198 10 false VCLU 5.708,1.031 6.167,1.229 0.458,0.198 10 false LVU 5.719,1.563 6.177,1.76 0.458,0.198 10 false ELU 5.406,2.031 5.719,2.229 0.313,0.198 10 false N37 5.417,2.219 6.958,2.417 1.542,0.198 10 false Urea Pump Control ECU 1.813,0.365 2.125,0.563 0.313,0.198 10 false 13 1.823,0.927 2.135,1.125 0.313,0.198 10 false 14 1.833,1.458 1.99,1.656 0.156,0.198 10 false 6 5.406,0.365 5.719,0.563 0.313,0.198 10 false 60 5.406,0.927 5.719,1.125 0.313,0.198 10 false 59 5.406,1.458 5.719,1.656 0.313,0.198 10 false 58

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT LEVEL SENSOR (UREA PUMP)
a.

Inspect the level sensor (urea pump).

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (LEVEL SENSOR - UREA PUMP CONTROL ECU)

NG

7.REPLACE UREA PUMP
2.CHECK HARNESS AND CONNECTOR (LEVEL SENSOR - UREA PUMP CONTROL ECU)
a.

Disconnect the urea pump connector.


b.

Disconnect the urea pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
x4-13 (VLV1) - N37-60 (VCLU) Always Below 1 Ω
x4-14 (LV1) - N37-59 (LVU) Always Below 1 Ω
x4-6 (ELV1) - N37-58 (ELU) Always Below 1 Ω
x4-13 (VLV1) or N37-60 (VCLU) - Body ground and other terminals Always 10 kΩ or higher
x4-14 (LV1) or N37-59 (LVU) - Body ground and other terminals Always 10 kΩ or higher
x4-6 (ELV1) or N37-58 (ELU) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK DTC OUTPUT

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Turn the ignition switch to ON and wait for 3 seconds or more.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

h.

Read the DTCs.


Result:
Result Proceed to
DTC P203A12 or P203A14 is output A
No DTC is output B



A

4.REPLACE UREA PUMP CONTROL ECU

B

END

4.REPLACE UREA PUMP CONTROL ECU

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Turn the ignition switch to ON and wait for 3 seconds or more.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE UREA PUMP

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED