Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2019.02–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0382589 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P246E11  Exhaust Gas Temperature Sensor 4 Bank 1 Circuit Short to Ground  P246E15  Exhaust Gas Temperature Sensor 4 Bank 1 Circuit Short to Battery or Open  


DESCRIPTION

A443538E01
2.26,2.083 2.51,2.469 2.51,2.469 5.104,2.469 true 3.75,2.073 4,2.458 true 4.208,0.698 4.688,0.698 4.688,0.698 5.073,1.448 true 4.25,2.083 4.5,2.469 true 0.125,1.615 1.052,1.865 0.927,0.25 10 false Exhaust Gas 1.75,0.604 4.302,0.865 2.552,0.26 10 false No. 4 Exhaust Gas Temperature Sensor 6.302,0.417 6.802,0.625 0.5,0.208 10 false ECM 5.198,2.396 6.219,2.604 1.021,0.208 10 false SCR Catalyst

The No. 4 exhaust gas temperature sensor is installed after the SCR catalyst to detect the exhaust gas temperature. A thermistor built into the No. 4 exhaust gas temperature sensor changes its resistance value according to the exhaust gas temperature. The lower the exhaust gas temperature, the higher the thermistor resistance value. The higher the exhaust gas temperature, the lower the thermistor resistance value. The No. 4 exhaust gas temperature sensor is connected to the ECM. The 5 V power source voltage is applied to the No. 4 exhaust gas temperature sensor from terminal THSO via resistor R.

Resistor R and the No. 4 exhaust gas temperature sensor are connected in series. When the resistance value of the No. 4 exhaust gas temperature sensor changes in accordance with the exhaust gas temperature, the voltage at terminal THSO also changes. The No. 4 exhaust gas temperature sensor monitors the temperature downstream of the SCR catalyst.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P246E11 Exhaust Gas Temperature Sensor 4 Bank 1 Circuit Short to Ground No. 4 exhaust gas temperature sensor output voltage is below 0.11 V for 3 seconds or more when all conditions are met (1 trip detection logic):
·

After starting the engine, 17 minutes or more elapses

·

Engine is running

·

Coolant temperature is 75°C (167°F) or higher


·

Open or short in No. 4 exhaust gas temperature sensor circuit

·

No. 4 exhaust gas temperature sensor

·

ECM


Comes on DTC stored SAE Code: P2470
P246E15 Exhaust Gas Temperature Sensor 4 Bank 1 Circuit Short to Battery or Open No. 4 exhaust gas temperature sensor output voltage is higher than 4.89 V for 3 seconds or more when all conditions are met (1 trip detection logic):
·

After starting the engine, 17 minutes or more elapses

·

Engine is running

·

Coolant temperature is 75°C (167°F) or higher


·

Open or short in No. 4 exhaust gas temperature sensor circuit

·

No. 4 exhaust gas temperature sensor

·

ECM


Comes on DTC stored SAE Code: P2471

Related Data List
DTC No. Data List
P246E11
P246E15
Exhaust Temperature B1S4

MONITOR DESCRIPTION

The ECM constantly monitors the output voltages from the No. 4 exhaust gas temperature sensors in order to detect problems with the sensors. When the sensor output voltage deviates from the normal operating range (between 0.11 V and 4.89 V) for more than 3 seconds after the engine is warmed up, the ECM interprets this as malfunction of the sensor circuit and illuminates the MIL.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P246E11
P246E15
Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher) and allowing 17 minutes to elapse after starting the engine.

WIRING DIAGRAM

A356866E06
2.302,1.354 2.917,1.552 0.615,0.198 10 false THSO 3.125,1.344 3.385,1.604 0.26,0.26 10 false E2 2.115,1.573 2.271,1.771 0.156,0.198 10 false 2 3.417,1.552 3.573,1.75 0.156,0.198 10 false 1 1.917,1.813 2.229,2.01 0.313,0.198 10 false Y2 1.927,1.99 4.469,2.396 2.542,0.406 10 false No. 4 Exhaust Gas Temperature Sensor 5.938,1.927 6.552,2.125 0.615,0.198 10 false E5 5.948,2.094 6.406,2.292 0.458,0.198 10 false ECM 5.552,0.583 6.167,0.781 0.615,0.198 10 false THSO 5.552,1.458 6.167,1.656 0.615,0.198 10 false E2 5.271,0.49 5.583,0.688 0.313,0.198 10 false 24 5.281,1.344 5.594,1.542 0.313,0.198 10 false 27

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT NO. 4 EXHAUST GAS TEMPERATURE SENSOR

Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NO. 4 EXHAUST GAS TEMPERATURE SENSOR - ECM)

NG

6.REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR
2.CHECK HARNESS AND CONNECTOR (NO. 4 EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Disconnect the No. 4 exhaust gas temperature sensor.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y2-2 (THSO) - E5-24 (THSO) Always Below 1 Ω
Y2-1 (E2) - E5-27 (E2) Always Below 1 Ω
Y2-2 (THSO) or E5-24 (THSO) - Body ground and other terminals Always 10 kΩ or higher
Y2-1 (E2) or E5-27 (E2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Start the engine.


f.

Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher) and allowing 17 minutes to elapse after starting the engine.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

6.REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED