Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2019.02–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0382589 ECD SYSTEM(w/ Urea SCR System) J

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  Fuel Injection System  


CAUTION / NOTICE / HINT

NOTICE:

After replacing an injector assembly, the ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION).


PROCEDURE

1.CHECK INJECTOR COMPENSATION CODE
a.

Check the injector compensation code.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Injector Compensation
50005 372 4596
Result:
Result Proceed to
Except below A
Compensation codes of the installed injector assemblies are the same as the compensation codes registered in the ECM B




A

2.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING

B

3.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (PROCEDURE 3)
2.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation codes.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Injector Compensation
50005 372 4596

b.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Pilot Quantity Learning
50005 372 4569

Result:
Proceed to
NEXT



NEXT

3.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (PROCEDURE 3)
3.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (PROCEDURE 3)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Common Rail (All).


d.

Take a snapshot of the following Data List items.

HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the list below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.

·

Check the Data List at idling and at 4000 rpm with no load after the engine is warmed up.




Result:
Proceed to
NEXT



NEXT

4.READ VALUE USING GTS (INJECTION FEEDBACK VALUE #1 TO #4 AND TARGET INJECTION VOLUME)
4.READ VALUE USING GTS (INJECTION FEEDBACK VALUE #1 TO #4 AND TARGET INJECTION VOLUME)
a.

Check Injection Feedback Value #1 to #4 and Target Injection Volume in the snapshot taken in procedure 3 when the engine was idling and at 4000 rpm with no load.

Result:
Result Proceed to
Injection Feedback Value for at least one cylinder is more than 5.0 mm3/st A
Target Injection Volume is less than 10.0 mm3/st at 4000 rpm B
Except above C


HINT:
·

When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Value to increase.

·

The ECM controls the system so that the sum of Injection Feedback Value for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Value for a cylinder is less than -5.0 mm3/st (-5.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Value for each of the other cylinders is 5.0 mm3/st or less, the injector assemblies are not malfunctioning.





A

5.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)

B

22.REPLACE INJECTOR ASSEMBLY OF ALL CYLINDERS

C

21.READ VALUE USING GTS (TARGET INJECTION VOLUME)
5.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)
HINT:

Use this Active Test to help determine whether a cylinder has compression loss or not.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed Cylinder #1 to #4.

Powertrain > Engine > Active Test
Active Test Display
Check the Cylinder Compression
Data List Display
Engine Speed Cylinder #1
Engine Speed Cylinder #2
Engine Speed Cylinder #3
Engine Speed Cylinder #4
50004 372 42028 134,135,136,137

d.

Check the engine speed during the Active Test.

Result:
Result Proceed to
Except below A
The values of Engine Speed Cylinder #1 to #4 are within 10 rpm of each other. B


HINT:

When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.




A

6.CHECK CYLINDER COMPRESSION PRESSURE

B

7.PERFORM PILOT QUANTITY LEARNING
6.CHECK CYLINDER COMPRESSION PRESSURE
a.

Check the cylinder compression pressure.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION

HINT:

When compression is low, there may be cracks in the piston or the injector assembly may be installed improperly.



Result:
Proceed to
OK
NG



OK

7.PERFORM PILOT QUANTITY LEARNING

NG

10.CHECK AND REPLACE PARTIAL ENGINE ASSEMBLY
7.PERFORM PILOT QUANTITY LEARNING
a.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Pilot Quantity Learning
50005 372 4569

Result:
Proceed to
NEXT



NEXT

8.READ VALUE USING GTS (INJECTION FEEDBACK VALUE #1 TO #4)
8.READ VALUE USING GTS (INJECTION FEEDBACK VALUE #1 TO #4)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine / Data List / Injection Feedback Value #1 to #4.

Powertrain > Engine > Data List
Tester Display
Injection Feedback Value #1
Injection Feedback Value #2
Injection Feedback Value #3
Injection Feedback Value #4
50003 372 977,978,979,980

e.

Read the values.

Standard:
GTS Display Engine Condition* Normal Value
Injection Feedback Value #1
Injection Feedback Value #2
Injection Feedback Value #3
Injection Feedback Value #4
Idling -5.0 mm3/st to 5.0 mm3/st


HINT:

*: The A/C switch and all accessory switches should be off, the engine coolant temperature should be 75°C (167°F) or more and the engine should be idled for 1 minute or more.


Result:
Result Proceed to
Injection Feedback Value for at least one cylinder is more than 5.0 mm3/st A
Except above B


HINT:
·

When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Value to increase.

·

The ECM controls the system so that the sum of Injection Feedback Value for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Value for a cylinder is less than -5.0 mm3/st (-5.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Value for each of the other cylinders is 5.0 mm3/st or less, the injector assemblies are not malfunctioning.





A

9.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

B

11.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
9.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
a.

Replace the injector assembly of the malfunctioning cylinder.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

23.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
10.CHECK AND REPLACE PARTIAL ENGINE ASSEMBLY
a.

Check and replace the engine assembly.


Result:
Proceed to
NEXT



NEXT

11.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
11.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak / Data List / Target Fuel Pressure (High) and Fuel Pressure (High).

Powertrain > Engine > Active Test
Active Test Display
Test the Fuel Leak
Data List Display
Target Fuel Pressure (High)
Fuel Pressure (High)
50004 372 42023 264,265

d.

Start the engine.


e.

Take a snapshot with the GTS during the Active Test.


f.

Measure the difference between the target fuel pressure (Target Fuel Pressure (High)) and the actual fuel pressure (Fuel Pressure (High)) when the "Test the Fuel Leak" Active Test is performed.

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


A227749E74
3.604,2.427 3.719,1.948 3.719,1.948 3.792,1.948 false 4.604,2.583 4.948,2.323 4.948,2.323 5.031,2.323 false 3.438,2.635 3.479,1.833 3.479,1.833 3.427,1.833 false 3.583,3.25 3.833,4.323 3.833,4.323 3.979,4.323 false 0.083,1.417 1.448,1.573 1.365,0.156 10 false Active Test Operation 0.083,0.583 1.479,0.781 1.396,0.198 10 false Engine Speed (rpm) 0.313,3.198 1.854,3.469 1.542,0.271 10 false Fuel Pressure (High) 3.802,1.865 5.74,2.031 1.938,0.167 10 false Target Fuel Pressure (High) 6.469,4.125 6.865,4.302 0.396,0.177 10 false Time 2.125,2.406 2.927,3.083 0.802,0.677 10 false Less than 10000 kPag 3,4.26 3.688,4.427 0.688,0.167 10 false 2 seconds 5.073,2.208 6.583,2.719 1.51,0.51 10 false Abnormal Fuel Pressure (High) 2.677,1.042 3.354,1.24 0.677,0.198 10 false Test Start 4.458,1.042 5.125,1.24 0.667,0.198 10 false Test Stop 5.885,1.042 6.563,1.24 0.677,0.198 10 false Test Start 2.073,1.76 3.427,2.188 1.354,0.427 10 false Normal Fuel Pressure (High) 1.646,0.271 2.021,0.438 0.375,0.167 10 false 2000 1.885,0.833 2.052,1 0.167,0.167 10 false 0 1.75,1.302 2.073,1.469 0.323,0.167 10 false ON 1.698,1.552 2.021,1.719 0.323,0.167 10 false OFF 4.021,4.25 5.948,4.708 1.927,0.458 10 false Pressure Discharge Valve Abnormal Fuel Pressure (High)

OK:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPag (102.0 kgf/cm2, 1451 psi).


Result:
Result Proceed to
NG A
OK* B


NOTICE:

*: Even when the results of the Active Test are normal, take a snapshot of vehicle data when the vehicle is accelerating. If "Fuel Pressure (High)" does not follow "Target Fuel Pressure (High)", proceed to step 12.

If "Fuel Pressure (High)" does not follow "Target Fuel Pressure (High)", the fuel filter element may be clogged.


HINT:
·

"Target Fuel Pressure (High)" means target fuel pressure controlled by the ECM.

·

"Fuel Pressure (High)" means actual fuel pressure in common rail assembly.

·

If the pressure discharge valve mounted on the common rail assembly is malfunctioning, the actual fuel pressure may change as indicated by "Pressure Discharge Valve Abnormal Fuel Pressure (High)" in the illustration.

·

The pressure discharge valve operates to discharge fuel pressure when the internal pressure of the common rail exceeds the target fuel pressure.

·

There are 2 fuel pressure sensor circuits and both of them display the same value. If the difference between Fuel Pressure (High) exceeds 10000 kPag (102 kgf/cm2, 1451 psi) for 2 seconds or more, it is necessary to inspect or repair the wiring for the fuel pressure sensor.





A

12.INSPECT PRESSURE DISCHARGE VALVE

B

20.READ VALUE USING GTS (FUEL PRESSURE (HIGH) AND TARGET FUEL PRESSURE (HIGH))
12.INSPECT PRESSURE DISCHARGE VALVE
a.

Enter the following menus: Powertrain / Engine / Utility / Pressure Discharge Valve Check.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION

Powertrain > Engine > Utility
Tester Display
Pressure Discharge Valve Check
50005 372 2573

b.

Select "Always Closed Check".


c.

Press "Next".


d.

Read the value of fuel pressure values.

OK:

Fuel pressure is properly maintained.


HINT:
·

If the fuel pressure cannot be maintained, the pressure discharge valve may not have a tight seal.

·

If the fuel pressure is being properly maintained, there are no problems with the sealing properties of the high-pressure fuel system. Therefore, an insufficient supply of fuel due to the fuel filter being clogged, or squashed or blocked low-pressure fuel pipes or hoses may be causing the reduction in common rail pressure.




Result:
Proceed to
OK
NG



OK

13.INSPECT CLOGGED FUEL PIPE

NG

18.REPLACE COMMON RAIL ASSEMBLY
13.INSPECT CLOGGED FUEL PIPE
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Target Fuel Pressure (High) and Fuel Pressure (High).

Powertrain > Engine > Data List
Tester Display
Target Fuel Pressure (High)
Fuel Pressure (High)
50003 372 264,265

d.

With no load after the engine is warmed up, take a snapshot when idling and vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear.


e.

Check the Target Fuel Pressure (High) and Fuel Pressure (High) value.

A261221E32
0.031,1.708 1.365,2.083 1.333,0.375 10 false Target Fuel Pressure (High) 3.844,2.125 6.427,2.271 2.583,0.146 10 false Normal Fuel Pressure (High) 3.708,0.344 5.969,0.542 2.26,0.198 10 false Abnormal Fuel Pressure (High)*1 0.104,0.031 2.635,0.198 2.531,0.167 10 false Fuel Pressure (High) During Idling 1.083,2.406 3.75,2.75 2.667,0.344 10 false Pressure varies periodically with a period of approximately 2 seconds or more 5.906,1.115 7.156,1.896 1.25,0.781 10 false Normal Condition: +/-5000 kPag (Idling after Engine Warmed Up)

Result:
Result Proceed to
While idling the vehicle, "Fuel Pressure (High)" deviates from the normal range and varies periodically with a period of approximately 2 seconds or more*1 A
"Fuel Pressure (High)" is normal while idling the vehicle, but "Fuel Pressure (High)" does not follow "Target Fuel Pressure (High)" when the accelerator pedal is fully depressed in 2nd gear*2
Except above B


NOTICE:
·

*1: The cause may be a squashed or blocked fuel pipe or hose.

·

*2: The cause may be a clogged fuel filter element assembly.





A

14.REPAIR OR REPLACE CLOGGED FUEL LINE

B

15.REPLACE FUEL SUPPLY PUMP ASSEMBLY
14.REPAIR OR REPLACE CLOGGED FUEL LINE
a.

Repair or replace the clogged (including frozen fuel) fuel pipe.


b.

Replace the fuel filter element assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL FILTER>REPLACEMENT

HINT:

If "Fuel Pressure (High)" does not follow "Target Fuel Pressure (High)" when the accelerator pedal is fully depressed in 2nd gear, replace the fuel filter element assembly.



Result:
Proceed to
NEXT



NEXT

19.BLEED AIR FROM FUEL SYSTEM
15.REPLACE FUEL SUPPLY PUMP ASSEMBLY
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.BLEED AIR FROM FUEL SYSTEM
16.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Result:
Proceed to
NEXT



NEXT

END

18.REPLACE COMMON RAIL ASSEMBLY
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>COMMON RAIL>REMOVAL


Result:
Proceed to
NEXT



NEXT

19.BLEED AIR FROM FUEL SYSTEM
19.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

20.READ VALUE USING GTS (FUEL PRESSURE (HIGH) AND TARGET FUEL PRESSURE (HIGH))
20.READ VALUE USING GTS (FUEL PRESSURE (HIGH) AND TARGET FUEL PRESSURE (HIGH))
a.

Check Fuel Pressure (High) and Target Fuel Pressure (High) in the snapshot taken in procedure 3 when the engine was idling.

Result:
Result Proceed to
Difference between Fuel Pressure (High) and Target Fuel Pressure (High) is 5000 kPag (51.0 kgf/cm2, 725 psi) or more B
Except above A




A

END

B

15.REPLACE FUEL SUPPLY PUMP ASSEMBLY
21.READ VALUE USING GTS (TARGET INJECTION VOLUME)
a.

Check Target Injection Volume in the snapshot taken in procedure 3 when the engine was idling.

Result:
Result Proceed to
Target Injection Volume while idling after engine warm up is more than 15 mm3/st A
Except above B


HINT:
·

Check that PM forced regeneration is not being performed.

·

The idling speed during PM forced regeneration is 800 to 1250 rpm (with the shift lever in neutral).





A

22.REPLACE INJECTOR ASSEMBLY OF ALL CYLINDERS

B

11.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
22.REPLACE INJECTOR ASSEMBLY OF ALL CYLINDERS
a.

Replace the injector assemblies of all cylinders.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

23.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
23.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Clean the fuel filter case and replace the fuel filter element assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL FILTER>REPLACEMENT

HINT:

Be sure to clean the inside of the fuel filter case as the injector assemblies may not operate properly if the fuel filter element assembly is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

24.BLEED AIR FROM FUEL SYSTEM
24.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

25.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
25.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation codes.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Injector Compensation
50005 372 4596

b.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Pilot Quantity Learning
50005 372 4569

Result:
Proceed to
NEXT



NEXT

11.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)